|
|
|
|
|
||||||||
|
|
|||||||||
| Home | Forums | Register | Gallery | FAQ | Calendar |
| Retailers | Community | News/Info | International Retailers | IRC | Today's Posts |
 |
|
|
Thread Tools |
June 5th, 2009, 23:11
|
#1 |
|
stuck mechbox.
hi, iam changing the spring in my CA m15a4 and i cant get the mechbox out of the lower receiver. it is loose but will not come out. what can i do.
thanks. Last edited by WilliamS; June 5th, 2009 at 23:31.. |
|
|
|
June 5th, 2009, 23:23
|
#2 |
|
so far out of here, Nasa started tracking
|
Did you take off the mag release clip.
__________________
okey dokey lokey |
|
|
|
|
June 5th, 2009, 23:28
|
#3 |
|
|
yeah i did. there is no pins or screws left holding the mechbox. i can move it but it just will not come out.
|
|
|
|
|
June 5th, 2009, 23:35
|
#4 |
|
so far out of here, Nasa started tracking
|
Did you take out the motor?
__________________
okey dokey lokey |
|
|
|
|
June 5th, 2009, 23:37
|
#5 | |
|
vision impaired
|
Never worked with armalites very much but I'd imagine www.mechbox.com will beable to show you a thing or two.
__________________
Quote:
|
|
|
|
|
|
June 5th, 2009, 23:40
|
#6 |
|
|
yes. i took every thing out and off. all that is left is the mechbox and the lower receiver. its just it won't come out.
|
|
|
|
|
June 5th, 2009, 23:41
|
#7 |
|
so far out of here, Nasa started tracking
|
Youtube as some good video's too.
__________________
okey dokey lokey |
|
|
|
|
June 5th, 2009, 23:44
|
#8 |
|
so far out of here, Nasa started tracking
|
Is it loose in the receiver,if yes try pulling from the back of the gearbox.And it helps putting it in auto.
__________________
okey dokey lokey |
|
|
|
|
June 5th, 2009, 23:46
|
#9 |
|
formerly Sepulcrum
|
need to kinda force it a little. It is a really tight fit, just make sure 100% there is nothing holding it in before you start forcing/wiggling it out.
|
|
|
|
|
June 5th, 2009, 23:46
|
#10 |
|
you took off the hand grip too right... may be asking the bleeding obvious
have to take off the stock Hand grip all the screws and pins and wiggle it a bit lower receiver may be tight |
|
|
|
|
June 5th, 2009, 23:49
|
#11 |
|
A-56 aka Mr.Hitman
|
Take off every single thing. Including the pistol grip which holds the screws to the mechbox shell.
If you have proceed, next step is to the the end of the mechbox (opposite side of the air nozzle) and lift it up first and wiggle it out. |
|
|
|
|
June 6th, 2009, 00:01
|
#12 |
|
|
the lower receiver is very tight..
|
|
|
|
|
June 6th, 2009, 00:08
|
#13 |
|
so far out of here, Nasa started tracking
|
be careful not to pull the motor wires out of the gearbox if it comes apart in a jerk.
__________________
okey dokey lokey |
|
|
|
|
June 6th, 2009, 00:22
|
#14 |
|
|
thanks guys. but it looks like its not willing to come out. ill try again later
|
|
|
|
|
June 6th, 2009, 00:31
|
#15 | ||
|
asexual lumbricus terrestris
|
*sigh*.... put the fire selector to SAFE, lift the front of the mechbox out, you should be able to pull the trigger, start lifting the back of the mechbox out, after that, if it becomes slightly stuck, push the mechbox towards the stock end of the reciever, and lift out again. If that doesn't work, you can grab the mechbox with 1 hand and give a gentle tap on the metal piece that the stock attaches on to. Make sure you don't lift by the nozzle or tear the wires, or whack the reciever too hard, which will tear the wires.
__________________
Quote:
Quote:
|
||
|
|
|
 |
|
||||||
| Bookmarks |
|
|
 |
|
