WE G39C stuck nozzle

Auto_Demon · August 15th, 2012, 21:43

So the nozzle in my bolt on my gun is stuck inside the bolt and i havent seen any decrease in gas efficiency but i would like to have it fixed, and one know how to fix this?

Ross · August 15th, 2012, 21:57

so if you pull on the nozzle it is actually jammed right in there? you'll probably have to disassemble the entire bolt carrier if it is.

Auto_Demon · August 16th, 2012, 00:43

I took the nozzle out of the bolt with some great effort, replaced the o-ring and lubed it as much as possible and its still getting stuck, after 1 magazine the nozzle is dry and needs relubing, i even put in a smaller diameter o-ring

Ross · August 16th, 2012, 00:48

Something is not right. does the nozzle look warped or cracked anywhere? The nozzle will dry out quickly, that's normal. propane does that. The oring itself should stay lubed. I use silicone grease instead of silicone oil. Does it get stuck by hand too, or only when the gun shoots?

Kos-Mos · August 16th, 2012, 00:52

Loosen the two guide rails screw by half a turn and play with the nozzle.. it will be alright.

These rails are made of a soft plastic and people over torque them all the time, so they warp and jam.

Auto_Demon · August 16th, 2012, 00:56

I will try and loosen the screws but one time when i was shooting it one of the screws came completely out, and Ross it gets stuck both by hand and when firing, when i pull back the bolt the nozzle does not move

Ross · August 19th, 2012, 22:33

Well if it gets stuck by hand. The nozzle is most likely warped. try replacing the nozzle.

Kos-Mos · August 19th, 2012, 22:46

Quote:

Originally Posted by Auto_Demon

I will try and loosen the screws but one time when i was shooting it one of the screws came completely out, and Ross it gets stuck both by hand and when firing, when i pull back the bolt the nozzle does not move

You know you have to put thread locker on every screw of the gun right? Otherwise it will break itself loose (not that bad on a G36).

If you remove both screws, you should be able to move the nozzle very easily. If not, the nozzle is warped or the bolt is warped (a lot less likely, but I have seen it).

Auto_Demon · August 20th, 2012, 21:41

k so i loosened he screwa a little bit and i put Frog Lube on the nozzle rails and its working better. the nozzle actualy moves!!! lol, well im selling the gun now so thanks for the help, buying the KWA LM4 soon, buying a quality gun :P

Fox62 · August 20th, 2012, 23:01

Quote:

Originally Posted by Auto_Demon

k so i loosened he screwa a little bit and i put Frog Lube on the nozzle rails and its working better. the nozzle actualy moves!!! lol, well im selling the gun now so thanks for the help, buying the KWA LM4 soon, buying a quality gun :P

...the G39 is a quality gun.

Fox.

Auto_Demon · August 21st, 2012, 14:36

ive had so many problems with my g39 and the trigger group has so many macgyvered parts in it

Kos-Mos · August 21st, 2012, 21:01

You mean you want to buy an other gun because the one you got was broken by the previous owner...

A NIB, stock G36 is a VERY good gun. I sold mine because I don't like the mags.

And mine had a full RATech kit in it... and worked like shit. I re-installed the stock parts and all was perfect.

jordan7831 · August 21st, 2012, 22:03

I miss my WE G36. The kick on that gun was wonderful. Seeing a misting of propane really added to the shooting experience and was great for making the house stink.

I sold mine because I was concerned about the plastic rails waring down eventually.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

August 15th, 2012, 21:43	#1
Auto_Demon Trader rating Join Date: Jun 2011 Location: Stonewall, MB	WE G39C stuck nozzle So the nozzle in my bolt on my gun is stuck inside the bolt and i havent seen any decrease in gas efficiency but i would like to have it fixed, and one know how to fix this? __________________ -KSC 1911A1 -Umarex springer P99 -WE M92 Marine grip - custom painted -KWA M11A1 NS2 Paintball: -Planet Eclipse Etha w/ Dye Rotor, Guardian 68/4500 tank

August 15th, 2012, 21:57	#2
Ross Trader rating Join Date: Nov 2009 Location: Winnipeg	so if you pull on the nozzle it is actually jammed right in there? you'll probably have to disassemble the entire bolt carrier if it is. __________________

August 16th, 2012, 00:43	#3
Auto_Demon Trader rating Join Date: Jun 2011 Location: Stonewall, MB	I took the nozzle out of the bolt with some great effort, replaced the o-ring and lubed it as much as possible and its still getting stuck, after 1 magazine the nozzle is dry and needs relubing, i even put in a smaller diameter o-ring __________________ -KSC 1911A1 -Umarex springer P99 -WE M92 Marine grip - custom painted -KWA M11A1 NS2 Paintball: -Planet Eclipse Etha w/ Dye Rotor, Guardian 68/4500 tank

August 16th, 2012, 00:48	#4
Ross Trader rating Join Date: Nov 2009 Location: Winnipeg	Something is not right. does the nozzle look warped or cracked anywhere? The nozzle will dry out quickly, that's normal. propane does that. The oring itself should stay lubed. I use silicone grease instead of silicone oil. Does it get stuck by hand too, or only when the gun shoots? __________________

August 16th, 2012, 00:56	#6
Auto_Demon Trader rating Join Date: Jun 2011 Location: Stonewall, MB	I will try and loosen the screws but one time when i was shooting it one of the screws came completely out, and Ross it gets stuck both by hand and when firing, when i pull back the bolt the nozzle does not move __________________ -KSC 1911A1 -Umarex springer P99 -WE M92 Marine grip - custom painted -KWA M11A1 NS2 Paintball: -Planet Eclipse Etha w/ Dye Rotor, Guardian 68/4500 tank

August 19th, 2012, 22:33	#7
Ross Trader rating Join Date: Nov 2009 Location: Winnipeg	Well if it gets stuck by hand. The nozzle is most likely warped. try replacing the nozzle. __________________

August 20th, 2012, 21:41	#9
Auto_Demon Trader rating Join Date: Jun 2011 Location: Stonewall, MB	k so i loosened he screwa a little bit and i put Frog Lube on the nozzle rails and its working better. the nozzle actualy moves!!! lol, well im selling the gun now so thanks for the help, buying the KWA LM4 soon, buying a quality gun :P __________________ -KSC 1911A1 -Umarex springer P99 -WE M92 Marine grip - custom painted -KWA M11A1 NS2 Paintball: -Planet Eclipse Etha w/ Dye Rotor, Guardian 68/4500 tank

August 21st, 2012, 14:36	#11
Auto_Demon Trader rating Join Date: Jun 2011 Location: Stonewall, MB	ive had so many problems with my g39 and the trigger group has so many macgyvered parts in it __________________ -KSC 1911A1 -Umarex springer P99 -WE M92 Marine grip - custom painted -KWA M11A1 NS2 Paintball: -Planet Eclipse Etha w/ Dye Rotor, Guardian 68/4500 tank

August 21st, 2012, 22:03	#13
jordan7831 will always be Mike Litoris in our hearts Trader rating Join Date: Jul 2004 Location: North York - Toronto	I miss my WE G36. The kick on that gun was wonderful. Seeing a misting of propane really added to the shooting experience and was great for making the house stink. I sold mine because I was concerned about the plastic rails waring down eventually.

WE G39C stuck nozzle

Doctor's Corner