My custom KSC Super G19 SBR

ILL9MIL · July 18th, 2005, 10:05

Base:
KSC Glock 19

Upgrades:
G&G metal slide
Shooter's Design CCW threaded outer barrel
KM SEALS 169mm silencer
**178mm 9Ball 6.03mm tightbore barrel**
Zenith recoil spring
Firefly rocket floating valve
Hidakaya floating valve spring
Custom floating valve retaining pin
Firefly impact hammer block (touch breech)
Hidakaya 150% hammer spring
Custom high flow mag valve (ported stock)
Custom blowback chamber springs
Hop-Up ball removed for ultimate power, accuracy, and consistancy
Guarder metal mag catch
Glock mag base plate
Hogue grip
**Tasco Optima 2000 Red Dot sight**
**FOBUS TAC telescoping Glock stock**
** Weaver Bipod**
Custom brace to allow cycling with any size/weight silencer and inner barrel

Power: 450fps with 0.20g BB using ET1600 Lanbo Red Gas

inner barrel

pokey · July 18th, 2005, 10:21

quite sweet. your silencer brace is very smart.

ILL9MIL · July 18th, 2005, 10:40

Thanks Pokey. Yeah the silencer brace is a must. The gun can cycle fine with my G&GSS100 silencer but the KM SEALS one is much too heavy, but the KM has a great foam material that actually makes quite a difference in the muzzle report. I plan on making an even longer inner barrel now that I have the brace, for extremely high power and accuracy.

CDN_Stalker · July 18th, 2005, 10:55

That is so fucked up looking it's cool!!!!! Very nice!

the end · July 18th, 2005, 14:14

very nice, but the bi-pod scares me a bit

Mr Jon · July 18th, 2005, 15:17

captainafternoon · July 18th, 2005, 15:39

Sweeeeeeeeeeeeeet!
Makes me want to get a KSC Glock 19 so bad now.

Relica Religia · July 18th, 2005, 16:14

Looks radical.

How did you end up installing the mag catch? I've been trying to replace mine but am having no luck.

ILL9MIL · July 18th, 2005, 16:36

What mag catch did you get, Guarder or G&G? Where are you getting stuck on the installation?

You need to take the slide off, then look down the mag well, you can see the vertical bar spring that goes in the mag catch, you need to use a flat head screw driver or something like it, to push the spring/bar over to the right (if the barrel end of the gun is facing away from you). the mag catch has a little slot all the way over to the right, that is where the spring goes in. So you push the spring all the way to the right then pull it outwards towards you to pop it out. Then just put the new one in and use the screwdriver to push the spring/bar back into the new one's slot and make sure you push it all the way over to the left so it is secure. If you are using a Guarder mag catch, you may need to use a small file to file down the top of the spring/bar because the Guarder mag catch slot is often not deep enough.

ILL9MIL · July 18th, 2005, 16:39

Phrozen, I was actually going to buy that bipod, then I decided I could use this other one to create the brace I've always wanted.

Glad you guys are diggin it. :-D

Dozer_01 · July 19th, 2005, 02:27

Not very practical at all (if even practical). However, looks kinda nifty. Good job!

conrad · July 19th, 2005, 03:37

1 question on my side, how much did all this set you back in total?

ILLusion · July 19th, 2005, 06:03

What gun is the 178mm inner barrel meant for?

Trader rating · July 19th, 2005, 09:16

hahahahahahahaha

ILL9MIL · July 19th, 2005, 10:01

Conrad The gun cost a bit over a $1000 American at this point.

Illusion The barrel is a 9ball tightbore made for the KSC M93R Auto 9 C. I had to do a little custom fitting to make it work (filing the sides flat where the hop up goes).

Dozer, I own 13 Glocks. This is my carbine, it's very practical for what it is. The stability and accuracy with this gun are insane compared to a hand-held pistol. Also, the telescoping stock and folding bipod make it quite compact to carry and it is quite light. So I have extreme power, accuracy, precision, and most importantly Glock durability. Try taking your AEG sniper weapon into a swamp...

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

July 18th, 2005, 10:05	#1
ILL9MIL Trader rating Join Date: Jul 2005 Location: VA	My custom KSC Super G19 SBR Base: KSC Glock 19 Upgrades: G&G metal slide Shooter's Design CCW threaded outer barrel KM SEALS 169mm silencer 178mm 9Ball 6.03mm tightbore barrel Zenith recoil spring Firefly rocket floating valve Hidakaya floating valve spring Custom floating valve retaining pin Firefly impact hammer block (touch breech) Hidakaya 150% hammer spring Custom high flow mag valve (ported stock) Custom blowback chamber springs Hop-Up ball removed for ultimate power, accuracy, and consistancy Guarder metal mag catch Glock mag base plate Hogue grip Tasco Optima 2000 Red Dot sight FOBUS TAC telescoping Glock stock Weaver Bipod Custom brace to allow cycling with any size/weight silencer and inner barrel Power: 450fps with 0.20g BB using ET1600 Lanbo Red Gas inner barrel

July 18th, 2005, 10:55	#4
CDN_Stalker Official ASC Bladesmith Trader rating Join Date: Jul 2003 Location: Ottawa, Ont.	That is so fucked up looking it's cool!!!!! Very nice! __________________ STKR Knives http://www.facebook.com/#!/pages/STK...17036668380871

July 18th, 2005, 15:17	#6
Mr Jon Trailer Park Supervisor Trader rating Join Date: Jul 2003 Location: Winnipeg MB	__________________

July 18th, 2005, 10:21	#2
pokey Trader rating Join Date: Apr 2004 Location: SasKat00N, SK	quite sweet. your silencer brace is very smart.

July 18th, 2005, 10:40	#3
ILL9MIL Trader rating Join Date: Jul 2005 Location: VA	Thanks Pokey. Yeah the silencer brace is a must. The gun can cycle fine with my G&GSS100 silencer but the KM SEALS one is much too heavy, but the KM has a great foam material that actually makes quite a difference in the muzzle report. I plan on making an even longer inner barrel now that I have the brace, for extremely high power and accuracy.

July 18th, 2005, 15:39	#7
captainafternoon mrlexmark Trader rating Join Date: Aug 2004 Location: Oakville, Ontario	Sweeeeeeeeeeeeeet! Makes me want to get a KSC Glock 19 so bad now.

July 18th, 2005, 16:14	#8
Relica Religia Trader rating Join Date: Dec 2004 Location: Kelowna, BC	Looks radical. How did you end up installing the mag catch? I've been trying to replace mine but am having no luck. __________________ Full auto.

July 18th, 2005, 16:36	#9
ILL9MIL Trader rating Join Date: Jul 2005 Location: VA	What mag catch did you get, Guarder or G&G? Where are you getting stuck on the installation? You need to take the slide off, then look down the mag well, you can see the vertical bar spring that goes in the mag catch, you need to use a flat head screw driver or something like it, to push the spring/bar over to the right (if the barrel end of the gun is facing away from you). the mag catch has a little slot all the way over to the right, that is where the spring goes in. So you push the spring all the way to the right then pull it outwards towards you to pop it out. Then just put the new one in and use the screwdriver to push the spring/bar back into the new one's slot and make sure you push it all the way over to the left so it is secure. If you are using a Guarder mag catch, you may need to use a small file to file down the top of the spring/bar because the Guarder mag catch slot is often not deep enough.

July 18th, 2005, 16:39	#10
ILL9MIL Trader rating Join Date: Jul 2005 Location: VA	Phrozen, I was actually going to buy that bipod, then I decided I could use this other one to create the brace I've always wanted. Glad you guys are diggin it. :-D

July 19th, 2005, 02:27	#11
Dozer_01 Trader rating Join Date: Sep 2003 Location: Ontario	Not very practical at all (if even practical). However, looks kinda nifty. Good job! __________________ LLTP

July 19th, 2005, 03:37	#12
conrad Trader rating Join Date: Nov 2004 Location: Vancouver ,BC	1 question on my side, how much did all this set you back in total? __________________ Current Arsenal: TM AK-47, KSC G19 Heavy Weight, 2 Academy TMP Springers Owned previously: KJ Vertec M9 Elite, Two no name m9 springers Current Project Gun: TM M14 OD, awaiting upgrade parts.

July 19th, 2005, 06:03	#13
ILLusion GBB Whisperer Trader rating Join Date: Jun 2002 Location: Toronto	What gun is the 178mm inner barrel meant for? __________________ *Advanced Airsoft Armaments and Enhancements* Quick to the gun, sure of your grip. Quick to the threat, sure of your shot. Diligentia, Vis, Celeritas Accuracy, Power, Speed

July 19th, 2005, 09:16	#14
Droc Guest Trader rating	hahahahahahahaha

July 19th, 2005, 10:01	#15
ILL9MIL Trader rating Join Date: Jul 2005 Location: VA	Conrad The gun cost a bit over a $1000 American at this point. Illusion The barrel is a 9ball tightbore made for the KSC M93R Auto 9 C. I had to do a little custom fitting to make it work (filing the sides flat where the hop up goes). Dozer, I own 13 Glocks. This is my carbine, it's very practical for what it is. The stability and accuracy with this gun are insane compared to a hand-held pistol. Also, the telescoping stock and folding bipod make it quite compact to carry and it is quite light. So I have extreme power, accuracy, precision, and most importantly Glock durability. Try taking your AEG sniper weapon into a swamp...

My custom KSC Super G19 SBR

Airsoft Media