|
|||||||||
|
Home | Forums | Register | Gallery | FAQ | Calendar |
Retailers | Community | News/Info | International Retailers | IRC | Today's Posts |
|
Thread Tools |
June 15th, 2011, 16:54 | #1 |
A&K M249 shitty airseal?
Having issues with my M249 I switched out everything in the gearbox and I can guarantee the leak isn't coming out of the piston/cylinder combo. I even switched out the original shitty hopup rubber and replaced it with a guarder clear one. But I'm still getting a massive FPS decrease even with a M110 spring.
Currently It's only shooting 340fps with that spring when it should be peaking out at 400fps which is kinda odd. Any idea on what it could be? |
|
June 15th, 2011, 20:21 | #2 |
The A&K uses a nozzle that is slightly different from other nozzles (it's longer for one). Go back to the stock Nozzle + cylinder head and you will have your issue fixed.
|
|
June 15th, 2011, 23:06 | #3 |
But here's the problem the stock nozzle has a terrible seal and leaks with barely any effort. Same with the piston. Also I replaced it with a nozzle of the exact same length, so that shouldn't be an issue right there.
|
|
June 15th, 2011, 23:32 | #4 |
Change the nub in the hop up, hop up rubber and check the hop up breech itself I have found a few of them were actually warped from the factory(bad casting) also look at the end part of your barrel some of the A&K M60 the end of barrel (hop up end) is slightly flared and deformed
|
|
June 16th, 2011, 04:17 | #5 |
Not Eye Safe, Pretty Boy Maximus on the field take his picture!
|
I make custom length steel air nozzles
|
June 16th, 2011, 09:53 | #6 |
Are you sure your barrel is properly seated and locked into position? A&K is known for bad airseal. Assuming you have the piston/piston head sealed good with your nozzle... Every A&K 249 user that I know of, has replaced the hopup unit with a Classic army one, replaced the rubber, and tried various hopup mods to make the hopup usable.
I have a mod of my own that is better than the tinned wire solution. Not sharing Unfortunately, this is often the best solution for some models of guns *sigh* |
|
June 16th, 2011, 10:03 | #7 |
That's kind of a dick move.
|
|
June 17th, 2011, 10:13 | #8 |
It is =P I did a LOT of reading and research to help someone with a his hopup problems in his new 249 and I came up with my own solution afterwards that is better as it provides good CONSISTENT hopup. I'm sure their are other people doing the same thing and keeping their mouths shut.
:fro: |
|
June 17th, 2011, 10:22 | #9 |
Why would you be posting in a gun doctor thread/section and not want to help people?
|
|
June 18th, 2011, 03:15 | #10 | |
Quote:
OP question is concerning airseal not bad hopup. |
||
June 18th, 2011, 12:34 | #11 |
Prancercise Guru
|
I've heard of some folks pouring silicon caulking in where the hopup chamber meets the inner barrel. Others will shim the spring that pushes the inner/outer barrel together for more pressure
Now on mine I found the outer barrel was being pushed forward. On the outer barrel there are 2 grub screws that hold the inner barrel in place. I took those out and found a longer set. Then I took 2 of the decorative screws off the outside of the receiver, you'll know which ones when you look. I threaded the longer bolts through the receiver into the outer barrel to pin it all together. Then I put the outer screws back in place and no more movement.
__________________
Airsoft, where nothing is hurt but feelings. |
June 19th, 2011, 00:53 | #12 | |
Quote:
Thanks for the tips. Last edited by sushicake; June 19th, 2011 at 00:55.. |
||
|
Bookmarks |
|
|