a little help with an upgrade? please?

Fidget11 · August 13th, 2006, 00:26

not sure if it belongs in this section but im going to be putting a full metal upgrade on my tm sig p226, and i need a little help taking the sig apart. from the diagrams and all that have been posted and exist in the manuals. however i get to a point where i have taken all the screws and pieces off i can and it doesnt seem to be coming all apart, namely the slide lock doesnt appear to be coming out. as well the hammer assembly doesnt seem be be coming out.

can someone with more experience in gbb's (especially if you have a p226 yourself) post up a bit of info for me to help me with the process?

thanks

Fidget11 · August 17th, 2006, 02:57

okay so i got the kit and i got it prettymuch all installed.... only thing is that parts 10 and 11 wont seem to go back in, no matter what i try that spring is just too soft and wont stay in place. although i have heard that it doesnt matter since the gun will work perfectly without them.

the other thing is that i need some suggestions on what to use to lube the slide/barrel because they are sitting very tight and i cant get the slide on because of it (well i could but i feel i would need alot of force to do that).

so any help would be greatly appreciated.

ILLusion · August 17th, 2006, 04:59

You have to file the slide rails down or you're going to cause damage and use waaaaaay more gas than you should.

Fitment should be done with NO internals installed

The slide has to be able to slide freely on the frame. Then install the blowback chamber and test the smoothness again. Then install the hammer assembly and test again. You're going to be taking parts in and out of the gun a lot as you get parts to fit. This is the most annoying part of GBB upgrades.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

August 13th, 2006, 00:26	#1
Fidget11 Trader rating Join Date: Apr 2006 Location: Edmonton, Alberta.	a little help with an upgrade? please? not sure if it belongs in this section but im going to be putting a full metal upgrade on my tm sig p226, and i need a little help taking the sig apart. from the diagrams and all that have been posted and exist in the manuals. however i get to a point where i have taken all the screws and pieces off i can and it doesnt seem to be coming all apart, namely the slide lock doesnt appear to be coming out. as well the hammer assembly doesnt seem be be coming out. can someone with more experience in gbb's (especially if you have a p226 yourself) post up a bit of info for me to help me with the process? thanks __________________ Stop Sulking About It! - Prioritize & Organize! - Canadian Airsoft Is Not A Crime! Primary: G36K Secondary: FMU SIG P226

August 17th, 2006, 02:57	#2
Fidget11 Trader rating Join Date: Apr 2006 Location: Edmonton, Alberta.	okay so i got the kit and i got it prettymuch all installed.... only thing is that parts 10 and 11 wont seem to go back in, no matter what i try that spring is just too soft and wont stay in place. although i have heard that it doesnt matter since the gun will work perfectly without them. the other thing is that i need some suggestions on what to use to lube the slide/barrel because they are sitting very tight and i cant get the slide on because of it (well i could but i feel i would need alot of force to do that). so any help would be greatly appreciated. __________________ Stop Sulking About It! - Prioritize & Organize! - Canadian Airsoft Is Not A Crime! Primary: G36K Secondary: FMU SIG P226

August 17th, 2006, 04:59	#3
ILLusion GBB Whisperer Trader rating Join Date: Jun 2002 Location: Toronto	You have to file the slide rails down or you're going to cause damage and use waaaaaay more gas than you should. Fitment should be done with NO internals installed The slide has to be able to slide freely on the frame. Then install the blowback chamber and test the smoothness again. Then install the hammer assembly and test again. You're going to be taking parts in and out of the gun a lot as you get parts to fit. This is the most annoying part of GBB upgrades. __________________ *Advanced Airsoft Armaments and Enhancements* Quick to the gun, sure of your grip. Quick to the threat, sure of your shot. Diligentia, Vis, Celeritas Accuracy, Power, Speed

a little help with an upgrade? please?

Doctor's Corner