|
|
|
|
|
||||||||
|
|
|||||||||
| Home | Forums | Register | Gallery | FAQ | Calendar |
| Retailers | Community | News/Info | International Retailers | IRC | Today's Posts |
 |
|
|
Thread Tools |
May 26th, 2015, 11:03
|
#1 |
|
VFC Trigger doesn't move on semi
Hi, I rewired my airsoft yesterday. Today, I re-assemble my gearbox and notify the trigger doesnt want to move in semi auto (exactly if the safety was at "on"), in full auto the trigger is working great.
__________________
Be gentle I'm French, If you don't undersetand what I say, just say it. |
|
|
|
May 26th, 2015, 11:21
|
#2 | ||
|
Oh we do hate you, just never felt like wasting the time to give you a user title :P
|
The model of gun will help us help you.
__________________
Quote:
Quote:
FinchFieldAirsoft |
||
|
|
|
|
May 26th, 2015, 11:23
|
#3 |
|
|
VFC VR16 Gen1
__________________
Be gentle I'm French, If you don't undersetand what I say, just say it. |
|
|
|
|
May 26th, 2015, 11:35
|
#4 | ||
|
Oh we do hate you, just never felt like wasting the time to give you a user title :P
|
Well there is only one peice inside the gearbox that can cause the trigger to not move.
in front of the trigger the little physical safety that stops the forward mortion on the trigger. If that bit is installed wrong the trigger may not move on semi. ill link a pic of how it should look but it should be flat on top and tapered on bottom.  not my pic, credit to the owner. But its the bit in front of the trigger. only other thing would be selector plate but it goes from safe to auto so likely not that.
__________________
Quote:
Quote:
FinchFieldAirsoft |
||
|
|
|
|
May 26th, 2015, 11:42
|
#5 |
|
|
wich way should I install the safety switch?
I installed it this way:  But I see a lot of picture who installed it this way:  not my picture
__________________
Be gentle I'm French, If you don't undersetand what I say, just say it. |
|
|
|
|
May 26th, 2015, 11:45
|
#6 |
|
Always install it the factory way.
__________________
The Steve has spoken. |
|
|
|
|
May 26th, 2015, 11:45
|
#7 |
|
|
__________________
Be gentle I'm French, If you don't undersetand what I say, just say it. Last edited by warplane95; May 26th, 2015 at 11:49.. |
|
|
|
|
May 26th, 2015, 12:03
|
#8 |
|
Prancercise Guru
|
Check your selector plate and safety disc also.
__________________
Airsoft, where nothing is hurt but feelings. |
|
|
|
|
May 26th, 2015, 12:28
|
#9 |
|
|
ok, look like it came from my cut off lever. How tight the screw from the cut off lever need to be?
Not tight at all tight, so the cut off lever will have a little bit of resistance super tight
__________________
Be gentle I'm French, If you don't undersetand what I say, just say it. |
|
|
|
|
May 26th, 2015, 12:45
|
#10 |
|
|
found it, the screw of my cut-off was too tight, thank you all
__________________
Be gentle I'm French, If you don't undersetand what I say, just say it. |
|
|
|
|
May 26th, 2015, 21:02
|
#11 |
|
|
Finally, look like it only work half -_-
https://www.youtube.com/watch?v=8U-VvKc0N90
__________________
Be gentle I'm French, If you don't undersetand what I say, just say it. |
|
|
|
|
May 27th, 2015, 01:45
|
#12 |
|
Squid Porn Superstar, I love the tentacles!
|
That is normal when you assemble the gearbox. It is the same thing as a semi auto seizure, except that you simply put the sector gear in that position when you assembled the box. Put the motor on, cycle the gun on auto and then semi should work.
|
|
|
|
 |
|
||||||
| Bookmarks |
|
|
 |
|
