difference between TM and G&P M4 bodies?

Mirodasc · October 18th, 2010, 19:37

Just as the title states, whats the difference between TM and G&P AEG bodies?
Are the tolerances different? Can a G&P upper fit on a TM lower? are they different sizes like the ICS bodies are longer?

Any information would be great, and if someone has both and could take a picture if there are differences, that would be much appreciated!

Thanks guys.

Strelok · October 18th, 2010, 19:40

G&P is pretty much made as aftermarket for TM

Most notable difference is G&P = Metal, TM = plastic.

Amos · October 18th, 2010, 19:46

TM is an old system that works off of body tabs with a two peice hop-up.

the G&P is made for the new system that's held in by the front pin and two smaller pins that fit into channels on the lower receiver. This system is for a 1 piece hop-up.

TokyoSeven · October 18th, 2010, 19:48

To summarize what Amos said in short, no a G&P upper will not mate properly with a TM lower due to the way parts connect.

Daiviet · October 18th, 2010, 19:49

you're going to need a 1 piece hop up instead of the two piece from TM if you're going to use a G&P metal body.

Mirodasc · October 18th, 2010, 20:05

So if I have a G&P Upper, I will need a 1 piece hop-up, and not a TM Lower. Other than that everything else should fit in fine? Pins, bolt, dust cover, gear box, selector level, etc?

TokyoSeven · October 18th, 2010, 20:59

Well as it stands you could get away with the two piece hopup since you only have the upper but unfortunately you wont be able to mate the G&P upper and TM lower because of different modes of attachment.

Best option currently would be to source a G&P lower and 1 piece hop up unit.

Skruface · October 19th, 2010, 01:34

Let's not forget that the delta ring threading of G&P uppers is NOT the same as the threading on a TM upper....

RecceGod · October 19th, 2010, 08:38

Quote:

Originally Posted by Skruface

Let's not forget that the delta ring threading of G&P uppers is NOT the same as the threading on a TM upper....

Oh yeah??? Well they used to...

Styrak · October 19th, 2010, 11:44

Quote:

Originally Posted by Skruface

Let's not forget that the delta ring threading of G&P uppers is NOT the same as the threading on a TM upper....

Yes it is....

Boyso · October 19th, 2010, 12:03

Hmm isn't the G&P using imperial threading and TM; metric?

If so, it is not the same... Yes you screw the same way, but it's different sizes.

Amos · October 19th, 2010, 12:05

At all depends on what generation body we're talking here...

I haven't had any problems putting new G&P front ends on older Marui style bodies.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

October 18th, 2010, 19:37	#1
Mirodasc Trader rating Join Date: May 2006 Location: Vancouver BC	difference between TM and G&P M4 bodies? Just as the title states, whats the difference between TM and G&P AEG bodies? Are the tolerances different? Can a G&P upper fit on a TM lower? are they different sizes like the ICS bodies are longer? Any information would be great, and if someone has both and could take a picture if there are differences, that would be much appreciated! Thanks guys.

October 18th, 2010, 19:46	#3
Amos Trader rating Join Date: Aug 2006 Location: Japan	TM is an old system that works off of body tabs with a two peice hop-up. the G&P is made for the new system that's held in by the front pin and two smaller pins that fit into channels on the lower receiver. This system is for a 1 piece hop-up. __________________ Custom Builds: FA3674U Krinkov G3SD6

October 18th, 2010, 19:48	#4
TokyoSeven Red Wine & Adderall Trader rating Join Date: Oct 2005 Location: Saskatoon, SK	To summarize what Amos said in short, no a G&P upper will not mate properly with a TM lower due to the way parts connect. __________________ "Its only a little bit on fire"

October 18th, 2010, 19:40	#2
Strelok Trader rating Join Date: Jun 2006 Location: Brandon Manitoba	G&P is pretty much made as aftermarket for TM Most notable difference is G&P = Metal, TM = plastic.

October 18th, 2010, 19:49	#5
Daiviet Captain Sunshine Trader rating Join Date: Aug 2006	you're going to need a 1 piece hop up instead of the two piece from TM if you're going to use a G&P metal body.

October 18th, 2010, 20:05	#6
Mirodasc Trader rating Join Date: May 2006 Location: Vancouver BC	So if I have a G&P Upper, I will need a 1 piece hop-up, and not a TM Lower. Other than that everything else should fit in fine? Pins, bolt, dust cover, gear box, selector level, etc?

October 18th, 2010, 20:59	#7
TokyoSeven Red Wine & Adderall Trader rating Join Date: Oct 2005 Location: Saskatoon, SK	Well as it stands you could get away with the two piece hopup since you only have the upper but unfortunately you wont be able to mate the G&P upper and TM lower because of different modes of attachment. Best option currently would be to source a G&P lower and 1 piece hop up unit. __________________ "Its only a little bit on fire"

October 19th, 2010, 12:03	#11
Boyso a.k.a. LastSpartan Trader rating Join Date: Jul 2009 Location: Québec city	Hmm isn't the G&P using imperial threading and TM; metric? If so, it is not the same... Yes you screw the same way, but it's different sizes. __________________ NEW BACON FOR SALE! "WHEN I DIE BURY ME UPSIDE DOWN SO THE WORLD CAN KISS MY ASS" -Platoon

October 19th, 2010, 12:05	#12
Amos Trader rating Join Date: Aug 2006 Location: Japan	At all depends on what generation body we're talking here... I haven't had any problems putting new G&P front ends on older Marui style bodies. __________________ Custom Builds: FA3674U Krinkov G3SD6

difference between TM and G&P M4 bodies?

Newbie Tank