|
|
|
|
|
||||||||
|
|
|||||||||
| Home | Forums | Register | Gallery | FAQ | Calendar |
| Retailers | Community | News/Info | International Retailers | IRC | Today's Posts |
 |
|
|
Thread Tools |
June 1st, 2007, 01:24
|
#16 |
|
also if you have any idea of whats going on other than convincing me to attempt to fuck up my gun please-share.
|
|
|
|
June 1st, 2007, 19:06
|
#17 | |
|
Quote:
i never said anything about getting your friend to do her... lol. in that case spit roast! but uh no, i lack experience with bad gun noises. i don't even know what that screw on the bottom does. but by the sounds of your problem your mech box probably has to come out anyway. that's the easy part. you may be able to see whats up if you take it out and look in it without taking it apart.
__________________
. |
||
|
|
|
|
June 4th, 2007, 21:56
|
#18 |
|
|
Okay im really studying how mechboxes work, im actually getting a hardon for this stuff. This is an idea i had while chattign with my doc
Amazing KG3 says: DOOD Amazing KG3 says: Gear Axel Tristan says: ya that could be fucked Amazing KG3 says: i think by pushing the motor to deep into the mechbox its offest the gears so that either the axel snapped or bushing came out and is obstructing the selctor Tristan says: exactl Tristan says: y Amazing KG3 says: also explains why it would whir, and no why it is jammed Tristan says: now you are thnking Amazing KG3 says: : D Amazing KG3 says: w00t Tristan says: but it could just be bent Amazing KG3 says: ill still replace it Tristan says: in any case new gears is the most likely part you will need Tristan says: well ya Worse case scenario, cracked mechbox, but i highly doubt that. |
|
|
|
|
June 4th, 2007, 22:19
|
#19 |
|
Not Eye Safe, Pretty Boy Maximus on the field take his picture!
|
that sick "whirrrrr" you described sounds to me like the motor is installed too deep. when you put the motor in did you run both red and black wires up the back of the motor, or one on each side? I did this once and the same thing happened (whoops, live and learn!) the wires need to both be run up the back of the pistol grip.
what kind of spring do you have installed? what brand of gears? check your air nozzle and see if it looks like its been hacked up |
|
|
|
|
June 4th, 2007, 23:09
|
#20 |
|
|
its all stock. And i do think the motor is up there to tight. I can see it being jammed but i know something busted in there. I heard a nasty noise.
|
|
|
|
|
June 5th, 2007, 14:51
|
#21 |
|
|
Damage report is in, this is what i need
-New gear set -New Spring (upgrade, not necessary) -New 7mm busings -New Bearings (Are these 7mm bushings?) -New mechbox body pin -Shims Do i need CA specific parts? Any guidance would be appreciated. |
|
|
|
|
June 5th, 2007, 15:41
|
#22 |
|
official report:
1x shattered bushing 1x damaged bushing 1x bent mechbox pin broken teeth on gears what a mess, the gears were totally siezed. thats what caused the whir sound.... sounded like a duck actually. anyways, any parts should do. only thing that needs to be CA is the mechbox pin. Last edited by wKnight; June 5th, 2007 at 15:45.. |
|
|
|
|
June 5th, 2007, 15:54
|
#23 |
|
Any gearset from any company would do
 Depending on if u want to upgrade or not, now would be a good timeAnd your 7mm bushings/bearings are the same thing i believe since they should be steel, relatively inexpensive New gearsets sometimes come with shims if not then buy a set which is about 10$ The gears would be the most expensive replacement, everything else should be about 20-30$ unless u get a very expensive spring But i have no idea where u would get a CA pin, if any M4 pins work just get some KA ones off ehobby they work
|
|
|
|
|
|
June 5th, 2007, 15:57
|
#24 |
|
|
ive got everything except for that friggin mechbox pin. I am told that CA needs a bigger pin as TM and ICS have smaller diameters. This is oversized, anyone kow if it will fit?
http://www.airsoftparts.ca/store2/in...roducts_id=306 |
|
|
|
|
June 5th, 2007, 16:01
|
#25 |
|
Those will fit... its just a very snug fit... very secure.
|
|
|
|
|
|
June 5th, 2007, 16:12
|
#26 |
|
|
thanks stokes, i just ordered it Xpress, hopefully itll be running soon.
|
|
|
|
|
June 5th, 2007, 18:01
|
#27 |
|
Not Eye Safe, Pretty Boy Maximus on the field take his picture!
|
I recommend buying mostly systema, and replace your tappet plate while your in there, the CA ones are extremely prone to failure lately.
7mm bearings are good, 7mm bushings would also work as an alternative, its 6mm bearings you need to stay away from. |
|
|
|
|
June 5th, 2007, 19:19
|
#28 |
|
|
i went with a Prometheus High speed gear set. Ill replace the tappet plate when i get a 9.6 battery.
|
|
|
|
 |
|
||||||
| Bookmarks |
| Thread Tools | |
|
|
 |
|
