ASCU technical discussion

venture · July 26th, 2011, 09:12

Thanks, Duy. I will try another data cable.

venture · July 27th, 2011, 01:21

Well, a new data cable fixed the problem. I believe the original was defective. I was so very careful with it, I cannot believe I damaged it. However, I do read that they are very delicate.

Ninja_En_Short · July 28th, 2011, 13:02

Hi everyone, question for you : Ijust installed an ASCU with the trigger and everything but the ASCU does not detect full auto, only semi, which means I only have semi auto available and can't program any other mode (only the the empty mag detection).
I folowed the manual except for the inner sticker I didn't have in the box.

Any ideas ?

MultipleParadox · July 28th, 2011, 19:28

Sticker should have been in the box, at least I had it when i gave it to you. Might have fallen somewhere, oh well, just make sure it wont short on the body :P

I don't have as much experience as you but is the cutoff lever moving freely? What about the contacts, are they meeting correctly?

coach · July 28th, 2011, 19:37

Inner sticker? You mean the bit they say to cover the selector plate to prevent contacting the receiver? Use duct tape on the receiver.

If it doesn't respond to full auto, ensure you trimmed enough of the selector plate. As you manually cycle the box without the spring in, make sure the cutoff lever doesn't touch the selector plate. Did you remove the cutoff lever spring?

Mjosr7 · July 28th, 2011, 21:23

My ASCU v2 did not come with a fuse. There is no mention of it in the manual.
What has been the norm with using this MOSFET? A little concerned and don't want to destroy this thing.

coach · July 28th, 2011, 21:42

I don't believe there is a fuse for the gen 2

phloudernow · July 29th, 2011, 13:33

try check the wires? if u did a cut maybe the wires aren't soldered on properly, i have the gen 1 installed on an M4 with a collapsable stock and that was a total nuisance for the gun doc, apparently one of the problems mine had was that so yer no idea tho bout the gen 2 ones still have to buy a few to try out

Ninja_En_Short · July 29th, 2011, 14:59

Cut off lever is springless and I believe I cut enough, yet selector is very hard, may have done something wrong there.

HKGhost · July 29th, 2011, 16:24

If everything was done correctly but it still won't shoot full auto, it could be that the ribbon cable is damaged or isn't plugged in all the way. Either try cleaning the connector or replace with another one.

Quote:

Originally Posted by Ninja_En_Short

Cut off lever is springless and I believe I cut enough, yet selector is very hard, may have done something wrong there.

ryan1796 · August 17th, 2011, 13:54

oh...I think I'm going to need some help too.

I installed it, re-installed it, and re-installed it again but the probelm of mine won't fixed.
My problem is now, it's won't shoot semi. No matter what I do, it shoots only full auto.
First off, it doesn't wanna go into the progamming mode at all. I only hear a beep when I pluged my battery and no more beep. It just keep shooting.
Can anyone give me an advise me on this? or is there any available Gun-Doc who is very familier to ASCU V2??

Forgot to mention it, it's am MP5A4.

MultipleParadox · August 17th, 2011, 14:20

Ryan, have you taken a look at the contact points of the ASCU and the selector plate if everything was in order?
If I'm correct, when on safe the selector plate shouldn't make any contact, in full it should contact all 3 points. I'm not sure on Semi though

ryan1796 · August 17th, 2011, 15:23

Quote:

Originally Posted by MultipleParadox

Ryan, have you taken a look at the contact points of the ASCU and the selector plate if everything was in order?
If I'm correct, when on safe the selector plate shouldn't make any contact, in full it should contact all 3 points. I'm not sure on Semi though

That's the biggest problem for me. Because I can't see where the selector plate is...I've tried look at it, but impossible..if it was M4, I'd just try put only the grip on the gear box and test it out but since it's MP5...I can't do that either.

MultipleParadox · August 17th, 2011, 15:44

Quote:

Originally Posted by ryan1796

That's the biggest problem for me. Because I can't see where the selector plate is...I've tried look at it, but impossible..if it was M4, I'd just try put only the grip on the gear box and test it out but since it's MP5...I can't do that either.

Oh, I don't even know what the Mp5's GB looks like, sorry I can't really help you on that matter then :/

ryan1796 · August 18th, 2011, 13:56

Quote:

Originally Posted by MultipleParadox

Oh, I don't even know what the Mp5's GB looks like, sorry I can't really help you on that matter then :/

It's same v2 gearbox bot on a different body and using a different selector plate..oh lord..

I'm looking for a Gun-doc who can properly install my ASCU~! I'll pay of course.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

July 26th, 2011, 09:12	#121
venture Trader rating Join Date: Jun 2005 Location: Halifax	Thanks, Duy. I will try another data cable. __________________ Visit us at :www.ventureairsoft.ca

July 27th, 2011, 01:21	#122
venture Trader rating Join Date: Jun 2005 Location: Halifax	Well, a new data cable fixed the problem. I believe the original was defective. I was so very careful with it, I cannot believe I damaged it. However, I do read that they are very delicate. __________________ Visit us at :www.ventureairsoft.ca

July 28th, 2011, 13:02	#123
Ninja_En_Short Trader rating Join Date: Jul 2007 Location: France, Canada (Montréal)	Hi everyone, question for you : Ijust installed an ASCU with the trigger and everything but the ASCU does not detect full auto, only semi, which means I only have semi auto available and can't program any other mode (only the the empty mag detection). I folowed the manual except for the inner sticker I didn't have in the box. Any ideas ? __________________ Tous les jours nous nous endormons plus instruits mais pas forcément moins bêtes... I can do a CTRL+ATL+DEL on your gun ! Gun doc in Montreal on AEG, GBB, GBBR and Bolt rifle (gaz and spring) Heavy custom builder (including painting)

July 28th, 2011, 19:37	#125
coach aka coachster Trader rating Join Date: Mar 2008 Location: T dot	Inner sticker? You mean the bit they say to cover the selector plate to prevent contacting the receiver? Use duct tape on the receiver. If it doesn't respond to full auto, ensure you trimmed enough of the selector plate. As you manually cycle the box without the spring in, make sure the cutoff lever doesn't touch the selector plate. Did you remove the cutoff lever spring?

July 28th, 2011, 21:23	#126
Mjosr7 Trader rating Join Date: Jul 2011 Location: New Jersey	Fuse necessity? If so what is the recommended. My ASCU v2 did not come with a fuse. There is no mention of it in the manual. What has been the norm with using this MOSFET? A little concerned and don't want to destroy this thing.

July 28th, 2011, 21:42	#127
coach aka coachster Trader rating Join Date: Mar 2008 Location: T dot	I don't believe there is a fuse for the gen 2

July 29th, 2011, 13:33	#128
phloudernow Trader rating Join Date: Nov 2010 Location: Toronto - Ontario, Vancouver - B.C and Hong Kong	try check the wires? if u did a cut maybe the wires aren't soldered on properly, i have the gen 1 installed on an M4 with a collapsable stock and that was a total nuisance for the gun doc, apparently one of the problems mine had was that so yer no idea tho bout the gen 2 ones still have to buy a few to try out __________________ Current Lineup: VFC HK416 Custom Custom Bowie Tactical x SAI Glock 17 (TM Base), Custom SAI BLU Glock Build (Timberwolf Base) Custom Zev Noveske Shooting Team Glock 34 Project Guns Custom Zev Dragonfly G17 (Project) (In progress)

July 29th, 2011, 14:59	#129
Ninja_En_Short Trader rating Join Date: Jul 2007 Location: France, Canada (Montréal)	Cut off lever is springless and I believe I cut enough, yet selector is very hard, may have done something wrong there. __________________ Tous les jours nous nous endormons plus instruits mais pas forcément moins bêtes... I can do a CTRL+ATL+DEL on your gun ! Gun doc in Montreal on AEG, GBB, GBBR and Bolt rifle (gaz and spring) Heavy custom builder (including painting)

August 17th, 2011, 13:54	#131
ryan1796 Trader rating Join Date: Apr 2009 Location: Calgary, AB	oh...I think I'm going to need some help too. I installed it, re-installed it, and re-installed it again but the probelm of mine won't fixed. My problem is now, it's won't shoot semi. No matter what I do, it shoots only full auto. First off, it doesn't wanna go into the progamming mode at all. I only hear a beep when I pluged my battery and no more beep. It just keep shooting. Can anyone give me an advise me on this? or is there any available Gun-Doc who is very familier to ASCU V2?? Forgot to mention it, it's am MP5A4.

ASCU technical discussion

Doctor's Corner