Glock Thread!

ILLusion · May 29th, 2013, 13:03

I hear you on all those points. But, knowing how Guarder's been with their quick engineering "solutions" in the past, I wouldn't be surprised if this never gets fixed.

I also just noticed that their photo of the front screw post is of the old version (lack of faux bar pins on the side). What are the chances I'll get these in my hands, and the post is actually re-engineered? LOL

Qlong · May 29th, 2013, 13:23

Quote:

Originally Posted by e-luder

+1 to that.

I recently found this mod out from some machinist around here and I'm testing it on their older frames. The flange helps ALOT. Although, i used JB Weld to create a makeshift flange around the casing. I have to find a better one for it and somehown elongate the post a bit longer. I takes a lot of work dremminling out the front chaisis and the stock safety to fit the flange too. In fact, doing this mod will almost mainly put that safety out of commission. We had to switch out to the other Guarder safety just to make the frame more accommodating. So much work for such a measely little part...

I doubt Guarder would make a drastic changes to that screw casing. Most people bought in to the whole brass casing thing already. They have to re- design it completely in my opinion or use better material. THeir frames in general are lousy in dimensions as well. At least when compared to the stock one... A Guarder slide with the Guarder frame never cycles right unless certain modifications are made. I mean...That says alot about their products...

Let us know if you make any progress on that!

Most of their slides make the BBU sit so low that the hammer gets caught on the BBU slide so you can't even cycle it. So then you end up taking the entire gun apart to fix it. Bleh.

Quote:

Originally Posted by ILLusion

I also just noticed that their photo of the front screw post is of the old version (lack of faux bar pins on the side). What are the chances I'll get these in my hands, and the post is actually re-engineered? LOL

Unfortunately Brian, it is their 2013 frame. If you look closer, that is the faux bar pin as it is sitting up that high. The trigger pin isn't visible from that view. You should totally talk to Guns Modify for their new frames!

e-luder · May 29th, 2013, 13:35

Quote:

Originally Posted by Qlong

Let us know if you make any progress on that!

Most of their slides make the BBU sit so low that the hammer gets caught on the BBU slide so you can't even cycle it. So then you end up taking the entire gun apart to fix it. Bleh.

Unfortunately Brian, it is their 2013 frame. If you look closer, that is the faux bar pin as it is sitting up that high. The trigger pin isn't visible from that view. You should totally talk to Guns Modify for their new frames!

Are those Available now???
I can't find anyone who stocks them!

ILLusion · May 29th, 2013, 13:55

I've talked to Guns Modify in the past, but I just can't meet their minimums - particularly for such a relatively small product line.

ebfud · June 4th, 2013, 03:05

Thanks for the heads up on the frames illusion.
So as promised more pics,
now added guns modify slide lock and trigger,
to create a cool two tone look

ILLusion · June 4th, 2013, 11:36

Just got confirmation from Guarder that the only real change to the new 2013 version frame, is that fake pin. :P That's the "new structure". LOL.

e-luder · June 4th, 2013, 16:46

Quote:

Originally Posted by ILLusion

Just got confirmation from Guarder that the only real change to the new 2013 version frame, is that fake pin. :P That's the "new structure". LOL.

Figures...

But dont they also have different markings? I think they have the European Glock trades on there instead...

ILLusion · June 6th, 2013, 00:24

Quote:

Originally Posted by e-luder

Figures...

But dont they also have different markings? I think they have the European Glock trades on there instead...

They have two versions... EU and US.

I have both coming in. Wasn't sure which one people were interested in...

ILLusion · June 20th, 2013, 20:31

Just got the frames... looking at them, the only real difference is that fake pin. I can't see any other immediate differences between the two, besides a very slight variance in shade (this is expected, and only really visible under very specific lighting conditions.)

Otherwise, texture, weight and feel are all the same.

ARC-74 · June 20th, 2013, 21:07

I did my own "New structure" on a HK3 Gen 4 frame

Fake pin added with small finishing nails, cut off most of the shaft, sanded the heads then cold blued them & superglued into some recesses/holes that I drilled out. (Camera battery needs charging, this is the only photo at the moment.)

Slighly zoomed in.

PaddMadd · August 16th, 2013, 03:12

Got rid of my MP7 and got a WE G17. I'll take a proper picture when I get my camera unpacked.

Hopefully planning to throw in an SAI trigger and slide, and stipple the shit out of the frame.

ARC-74 · August 23rd, 2013, 13:00

PGC G17 & Detonator G19 silver slides. PGC has more of a satin finish compared to the Detonator matt finish.

N_Force · October 27th, 2013, 02:12

ARC-74 · December 11th, 2013, 22:09

Another experiment with DuraCoat, this time the color is Parker, the subject is a PGC slide that was sanded with 600 grit as opposed to being sand blasted.

docholiday · December 16th, 2013, 18:53

My TM Glock.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

May 29th, 2013, 13:03	#496
ILLusion GBB Whisperer Trader rating Join Date: Jun 2002 Location: Toronto	I hear you on all those points. But, knowing how Guarder's been with their quick engineering "solutions" in the past, I wouldn't be surprised if this never gets fixed. I also just noticed that their photo of the front screw post is of the old version (lack of faux bar pins on the side). What are the chances I'll get these in my hands, and the post is actually re-engineered? LOL __________________ *Advanced Airsoft Armaments and Enhancements* Quick to the gun, sure of your grip. Quick to the threat, sure of your shot. Diligentia, Vis, Celeritas Accuracy, Power, Speed Last edited by ILLusion; May 29th, 2013 at 13:06..

May 29th, 2013, 13:55	#499
ILLusion GBB Whisperer Trader rating Join Date: Jun 2002 Location: Toronto	I've talked to Guns Modify in the past, but I just can't meet their minimums - particularly for such a relatively small product line. __________________ *Advanced Airsoft Armaments and Enhancements* Quick to the gun, sure of your grip. Quick to the threat, sure of your shot. Diligentia, Vis, Celeritas Accuracy, Power, Speed

June 4th, 2013, 11:36	#501
ILLusion GBB Whisperer Trader rating Join Date: Jun 2002 Location: Toronto	Just got confirmation from Guarder that the only real change to the new 2013 version frame, is that fake pin. :P That's the "new structure". LOL. __________________ *Advanced Airsoft Armaments and Enhancements* Quick to the gun, sure of your grip. Quick to the threat, sure of your shot. Diligentia, Vis, Celeritas Accuracy, Power, Speed

June 20th, 2013, 20:31	#504
ILLusion GBB Whisperer Trader rating Join Date: Jun 2002 Location: Toronto	Just got the frames... looking at them, the only real difference is that fake pin. I can't see any other immediate differences between the two, besides a very slight variance in shade (this is expected, and only really visible under very specific lighting conditions.) Otherwise, texture, weight and feel are all the same. __________________ *Advanced Airsoft Armaments and Enhancements* Quick to the gun, sure of your grip. Quick to the threat, sure of your shot. Diligentia, Vis, Celeritas Accuracy, Power, Speed

June 20th, 2013, 21:07	#505
ARC-74 Can't Aim worth a damn!! old lady gives me heck for missing the toilet all the time. Trader rating Join Date: Apr 2011 Location: Montreal area & Tatooine	I did my own "New structure" on a HK3 Gen 4 frame Fake pin added with small finishing nails, cut off most of the shaft, sanded the heads then cold blued them & superglued into some recesses/holes that I drilled out. (Camera battery needs charging, this is the only photo at the moment.) Slighly zoomed in. __________________ Insert name here: Last edited by ARC-74; June 20th, 2013 at 21:18..

August 23rd, 2013, 13:00	#507
ARC-74 Can't Aim worth a damn!! old lady gives me heck for missing the toilet all the time. Trader rating Join Date: Apr 2011 Location: Montreal area & Tatooine	PGC G17 & Detonator G19 silver slides. PGC has more of a satin finish compared to the Detonator matt finish. __________________ Insert name here: Last edited by ARC-74; August 27th, 2013 at 13:11..

October 27th, 2013, 02:12	#508
N_Force Trader rating Join Date: Oct 2006 Location: Toronto, Ontario	__________________ aka Uncle

December 11th, 2013, 22:09	#509
ARC-74 Can't Aim worth a damn!! old lady gives me heck for missing the toilet all the time. Trader rating Join Date: Apr 2011 Location: Montreal area & Tatooine	Another experiment with DuraCoat, this time the color is Parker, the subject is a PGC slide that was sanded with 600 grit as opposed to being sand blasted. __________________ Insert name here: Last edited by ARC-74; December 11th, 2013 at 23:12..

December 16th, 2013, 18:53	#510
docholiday docholidayy Trader rating Join Date: Feb 2012 Location: Toronto	My TM Glock.

Glock Thread!

Airsoft Media