|
|||||||||
|
Home | Forums | Register | Gallery | FAQ | Calendar |
Retailers | Community | News/Info | International Retailers | IRC | Today's Posts |
|
Thread Tools |
January 8th, 2010, 08:20 | #1 |
Slow mo.
|
Sticky / Stuck Slide?
I put together this Kimber Warrior with a metal Nova kit and all seemed fine until I started shooting it. First the trigger didn't work about 20% of the time, and when I thought I fixed that another problem arose. Once the trigger is pulled, the slide proceeds with its normal functions. I know it blows back because I can feel it kick, but what I don't know is how it gets stuck in the position you see in the pictures. It feels like the tolerance is too tight between the slide and its rails and I have to use strength to unstick it before manually racking it and sling shotting it back to battery. This happens very often. It has been lubed and racked a million times so I don't know what's wrong.
Internal upgrades: - Recoil and Hammer springs - KM High Flow Valve - Tanio Koba Twist Inner Barrel - Firefly Hop up rubber I do not know if any of these upgrades can be a factor in the aforementioned problem, but I listed them to let you know what I have replaced in the gun. Has anybody else had this problem before with their guns? Does anybody have a solution? Or perhaps a diagnosis? Any help is HUGELY appreciated. I just finished building this baby and want to shoot her without something going wrong.
__________________
The ultimate measure of a man is not where he stands in moments of comfort and convenience, but where he stands at times of challenge and controversy. - Martin Luther King, Jr. Last edited by Slono; January 8th, 2010 at 08:23.. |
January 8th, 2010, 08:30 | #2 |
Tys
|
Looks like the edge of your hammer is getting caught on the inside of the blowback unit when the slide is being returned to battery.
Do you have a 150% hammer spring in there? If so, just as a check...swap it back to stock and see if it goes away. Also...when it's stuck...if you reach in there and gently pull the hammer down a hair...does the slide continue forward? You can polish the part on the BBU that it's catching...and/or the tip of the part of the hammer it's catching. I've re-beveled a couple of hammers to fix this. Doesn't take much...just take a close look at it when it's catching to see what angle to change it to. Tys |
January 8th, 2010, 19:33 | #3 |
Slow mo.
|
I replaced the upgraded recoil spring with the stock spring and it still gets stuck about 90% of the time, except the slide gets stuck a little farther back. The slide catch is almost at the slide catch notch where the slide can lock back. The weird thing is that the mag is never empty when that happens so it shouldn't go back that far.
And like with the upgraded recoil spring, once it gets stuck, any space between the receiver and slide becomes so tight that there's almost no movable space. Its like something along the rails are forcing them together. I examined the rails but everything is completely flat. Edit: I can still slide it back and forth even when it feels really tight and there's a point where if I move it fast enough with force or forward enough (nearish to resting / battery position) OR back enough (nearly fully cocked back), something makes a clicking noise and I can feel something move or change within the receiver. Once it clicks it slides smoothly again. Is this a rail misalignment or something to do with the hammer assembly? Hammer assembly = all the little pieces that work together to move the hammer. If there's a specific name for those pieces I would like to know so I don't have to make names up or use the wrong ones.
__________________
The ultimate measure of a man is not where he stands in moments of comfort and convenience, but where he stands at times of challenge and controversy. - Martin Luther King, Jr. Last edited by Slono; January 8th, 2010 at 22:18.. |
January 8th, 2010, 23:02 | #4 |
When it gets caught, if you push the outer barrel from the tip inward, will the slide cycle?
|
|
January 8th, 2010, 23:13 | #5 |
Slow mo.
|
No. The outer barrel goes in a touch when I push it but the slide will not cycle.
__________________
The ultimate measure of a man is not where he stands in moments of comfort and convenience, but where he stands at times of challenge and controversy. - Martin Luther King, Jr. |
January 8th, 2010, 23:26 | #6 |
Does the slide move smoothly without all the internal? Does it move smoothly with BBU but without the barrel/recoil spring assy?
|
|
January 8th, 2010, 23:58 | #7 | |
Slow mo.
|
Quote:
Actually, there was one incident when I racked it back with the mag in and on the first rack back it got stuck before I could rack it back completely. I tested all 3 mags I had, 2 of which were completely new and it wasn't the mags that were the problem. The feeding lip and everything was not scratched. Edit: I found out that the slide is actually hitting the piece with the little spring on the LEFT side of the gun. When the slide gets stuck it has already gone over the sear disconnector so that is not the problem.
__________________
The ultimate measure of a man is not where he stands in moments of comfort and convenience, but where he stands at times of challenge and controversy. - Martin Luther King, Jr. Last edited by Slono; January 9th, 2010 at 00:15.. |
|
January 9th, 2010, 00:29 | #8 |
Did you tighten the blow back unit into the slide really tight.
I find the tightness of this affects my slide cycle. I just tightn it to the point where it stops gently and then play around( i use blue thread lock)
__________________
|
|
January 9th, 2010, 00:32 | #9 |
Official ASC "Dumb Ass"
|
yes, same here I usually let gravity settle the BBU in and then tighten the screw slowly while watching to see if the unit is "passing" the rails
__________________
|
January 9th, 2010, 00:51 | #10 | |
Slow mo.
|
Quote:
It is passing the rails. Unless a nano-metre makes a difference in the way the slide moves.
__________________
The ultimate measure of a man is not where he stands in moments of comfort and convenience, but where he stands at times of challenge and controversy. - Martin Luther King, Jr. |
|
January 9th, 2010, 01:03 | #11 | |
Slow mo.
|
Quote:
It is passing the rails. Unless a nanometre makes a difference in the way the slide moves.
__________________
The ultimate measure of a man is not where he stands in moments of comfort and convenience, but where he stands at times of challenge and controversy. - Martin Luther King, Jr. |
|
January 9th, 2010, 01:04 | #12 |
Official ASC "Dumb Ass"
|
loosen the screw a bit n see if it moves back and forth smoothly, then tighten it up to the point that it still works
*edit Also make sure that ur rear sight is seated correctly and that the top of the bbu is mating correctly with it.
__________________
Last edited by pusangani; January 9th, 2010 at 01:09.. |
January 9th, 2010, 01:24 | #13 |
Slow mo.
|
To my understanding if the rear sight was not mating correctly with the top of the BBU that would mean the BBU would be pushed down and it wouldn't line up with the rails. There is a small gap between my rear sight and the slide, but the BBU is sitting flush with the rails so the sight probably isn't the issue.
__________________
The ultimate measure of a man is not where he stands in moments of comfort and convenience, but where he stands at times of challenge and controversy. - Martin Luther King, Jr. |
January 9th, 2010, 01:52 | #14 |
Slow mo.
|
Update:
I found out the it only gets stuck when the mag is it in. I'm re-lubricating it and I found out accidentally that when I put the mag in and rack it gets stuck about 5% - 10% of the time.
__________________
The ultimate measure of a man is not where he stands in moments of comfort and convenience, but where he stands at times of challenge and controversy. - Martin Luther King, Jr. Last edited by Slono; January 9th, 2010 at 01:55.. |
January 9th, 2010, 02:13 | #15 |
How much material did you remove(if at all) from the bottom of the BBU?
|
|
|
Bookmarks |
Thread Tools | |
|
|