KSC G19 High Output Valves

sushi_boy604 · May 14th, 2009, 01:43

I recently bought 3 high output valve for 3 of my KSC G19 mags. The problem is, theres no power and more gas consumption and its even worse when i replace the valves back to stock.
The usage for gas is a lot less and the power weakens after 10 consecutive shots. At first, 1 of the 3 mags worked. Then i figured it was something wrong with the other two valves. So i replaced the "working" valve with one of the "non-working" valve. It didn't work. I then replaced back the "working" valve to the original mag; now i have 3 "non-working" mags with high valves in it. So i figured this brand of valve maybe crap. So i replaced one mag with the stock valve. A little bit of power but more gas consumption than before; just as bad as the valve.
So what did i do? I might have dropped more silicone oil in the mags than i should have. Would that have made a difference? Can a new bottle of propane that i am using be faulty? Was there something i had to do before installing the valves to the mag? Anything would be great. Thanks.

ILLusion · May 14th, 2009, 18:49

Make sure you don't tighten them too much (it pinches the o-ring), also make sure one of the exit ports (the largest one if there are varying sizes) are pointing straight up at the release port.

sushi_boy604 · May 14th, 2009, 19:37

Thanks ILLusion. I also noticed the hop up rubber is broken. would that make a difference as well?

ILLusion · May 14th, 2009, 19:41

Yes

sushi_boy604 · May 14th, 2009, 21:55

Update: 2 of the 3 mags now work thanks to ILLusion. I think this is a new problem now. This one mag won't seem to give out power plus it has a high gas consumption. I used both stock and hi flow valves and none of them seem to make a difference. Its like it doesn't fill up the mag with propane unlike the other 2.

ILLusion · May 14th, 2009, 22:38

What brand valves are you using?

sushi_boy604 · May 14th, 2009, 23:21

Action

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

May 14th, 2009, 01:43	#1
sushi_boy604 Trader rating Join Date: Jun 2008 Location: British Columbia	KSC G19 High Output Valves I recently bought 3 high output valve for 3 of my KSC G19 mags. The problem is, theres no power and more gas consumption and its even worse when i replace the valves back to stock. The usage for gas is a lot less and the power weakens after 10 consecutive shots. At first, 1 of the 3 mags worked. Then i figured it was something wrong with the other two valves. So i replaced the "working" valve with one of the "non-working" valve. It didn't work. I then replaced back the "working" valve to the original mag; now i have 3 "non-working" mags with high valves in it. So i figured this brand of valve maybe crap. So i replaced one mag with the stock valve. A little bit of power but more gas consumption than before; just as bad as the valve. So what did i do? I might have dropped more silicone oil in the mags than i should have. Would that have made a difference? Can a new bottle of propane that i am using be faulty? Was there something i had to do before installing the valves to the mag? Anything would be great. Thanks.

May 14th, 2009, 18:49	#2
ILLusion GBB Whisperer Trader rating Join Date: Jun 2002 Location: Toronto	Make sure you don't tighten them too much (it pinches the o-ring), also make sure one of the exit ports (the largest one if there are varying sizes) are pointing straight up at the release port. __________________ *Advanced Airsoft Armaments and Enhancements* Quick to the gun, sure of your grip. Quick to the threat, sure of your shot. Diligentia, Vis, Celeritas Accuracy, Power, Speed

May 14th, 2009, 19:41	#4
ILLusion GBB Whisperer Trader rating Join Date: Jun 2002 Location: Toronto	Yes __________________ *Advanced Airsoft Armaments and Enhancements* Quick to the gun, sure of your grip. Quick to the threat, sure of your shot. Diligentia, Vis, Celeritas Accuracy, Power, Speed

May 14th, 2009, 19:37	#3
sushi_boy604 Trader rating Join Date: Jun 2008 Location: British Columbia	Thanks ILLusion. I also noticed the hop up rubber is broken. would that make a difference as well?

May 14th, 2009, 21:55	#5
sushi_boy604 Trader rating Join Date: Jun 2008 Location: British Columbia	Update: 2 of the 3 mags now work thanks to ILLusion. I think this is a new problem now. This one mag won't seem to give out power plus it has a high gas consumption. I used both stock and hi flow valves and none of them seem to make a difference. Its like it doesn't fill up the mag with propane unlike the other 2.

May 14th, 2009, 22:38	#6
ILLusion GBB Whisperer Trader rating Join Date: Jun 2002 Location: Toronto	What brand valves are you using? __________________ *Advanced Airsoft Armaments and Enhancements* Quick to the gun, sure of your grip. Quick to the threat, sure of your shot. Diligentia, Vis, Celeritas Accuracy, Power, Speed

May 14th, 2009, 23:21	#7
sushi_boy604 Trader rating Join Date: Jun 2008 Location: British Columbia	Action

KSC G19 High Output Valves

Doctor's Corner