Airsoft Canada
http://triggerairsoft.com/shop/

Go Back   Airsoft Canada > Discussion > Doctor's Corner
Home Forums Register Gallery FAQ Calendar
Retailers Community News/Info International Retailers IRC Today's Posts

TM P226 question

:

Doctor's Corner

Reply
 
Thread Tools
Old October 15th, 2007, 17:25   #1
Maverickmarc
 
Join Date: Sep 2007
Location: Barrie
Send a message via MSN to Maverickmarc
TM P226 question

Just got it in today. Lubed it up. Ran a mag throught it and decided to take it apart. just the slide though. Slide comes off no problem. Dropped sum silicone oil were the slide moves and now it wont go back in all the way. Theres like a feww milimetres left for it to go. WTF!! I'm gonna rage..
Someone help before I do
Maverickmarc is offline   Reply With Quote
Old October 15th, 2007, 17:28   #2
Renegade)
A Total Bastard
 
Renegade)'s Avatar
 
Join Date: Apr 2006
Location: Tottenham, Ontario
Chill before you break it man, push down the silver peice on the left side of the hammer assembly, this engages the firing pin, the slide wont go back unless this is locked down or able to move freely. When the pin is back, the lever is locked, but when it pin is released, the lever can move up and down allowing the slide to rack back fully.

Im in Orillia BTW, so if you need a 226 lesson/walk through, and age verification, come for a 20 minute drive in the future.
__________________
W1-5
Renegade) is offline   Reply With Quote
Old October 15th, 2007, 17:35   #3
Maverickmarc
 
Join Date: Sep 2007
Location: Barrie
Send a message via MSN to Maverickmarc
i'm looking @ the hammer assembly. the only silver piece in the is on the left side if ur looking down the gun. it moves up and down but its spring loaded and comes back up.
Maverickmarc is offline   Reply With Quote
Old October 15th, 2007, 17:38   #4
Maverickmarc
 
Join Date: Sep 2007
Location: Barrie
Send a message via MSN to Maverickmarc
the slide moves freely and almost comes back, theres just a few mm left for it to be on properly
Maverickmarc is offline   Reply With Quote
Old October 15th, 2007, 17:38   #5
Renegade)
A Total Bastard
 
Renegade)'s Avatar
 
Join Date: Apr 2006
Location: Tottenham, Ontario
as long as it moves up and down, and the hammer is locked back, the slide should slide right on and all the way back allowing you to relock the release lever. Try it again, if not, dont force it, pull the slide back off, pull the trigger to release the hammer, then recock it and try to put the slide back on.

Let me know.
__________________
W1-5
Renegade) is offline   Reply With Quote
Old October 15th, 2007, 17:42   #6
Maverickmarc
 
Join Date: Sep 2007
Location: Barrie
Send a message via MSN to Maverickmarc
no luck
Maverickmarc is offline   Reply With Quote
Old October 15th, 2007, 17:45   #7
Maverickmarc
 
Join Date: Sep 2007
Location: Barrie
Send a message via MSN to Maverickmarc
its almost there
Maverickmarc is offline   Reply With Quote
Old October 15th, 2007, 17:45   #8
johnnyrico
 
johnnyrico's Avatar
 
Join Date: Apr 2002
Location: Winnipeg, MB
When putting the P226 slide back on, if you just slide it on it will stop about 2 mm or so from the normal place.

I noticed that you have to use your thumb to push the slide/barrel back that 2mm abit, and then flick the disassembly switch back up.

I hope this info helps.
__________________
"Banning firearms to prevent criminal use of guns is about as smart as banning
marriage to prevent spousal abuse, or banning pregnancy to prevent child abuse. "

"When just seconds can mean life or death, the police are just minutes away"

"If you can read this, thank a teacher... Since it's in English, thank a soldier"
johnnyrico is offline   Reply With Quote
Old October 15th, 2007, 17:48   #9
Maverickmarc
 
Join Date: Sep 2007
Location: Barrie
Send a message via MSN to Maverickmarc
i'm trying to force that 2mm a bit but not to hard. it won't budge
Maverickmarc is offline   Reply With Quote
Old October 15th, 2007, 17:48   #10
Renegade)
A Total Bastard
 
Renegade)'s Avatar
 
Join Date: Apr 2006
Location: Tottenham, Ontario
hmm, im not sure what it could be, bent hammer rod, mag in? lever isnt aimed down(how u turn it to release the slide) maybe the recoil spring rod is not in correctly?

Take this to msn if you want.. easier to work on there.
__________________
W1-5
Renegade) is offline   Reply With Quote
Old October 15th, 2007, 17:48   #11
Maverickmarc
 
Join Date: Sep 2007
Location: Barrie
Send a message via MSN to Maverickmarc
but thats definatly where its stopping, its like its caught on something
Maverickmarc is offline   Reply With Quote
Old October 15th, 2007, 17:49   #12
Maverickmarc
 
Join Date: Sep 2007
Location: Barrie
Send a message via MSN to Maverickmarc
maverickmarc@hotmail.com
Maverickmarc is offline   Reply With Quote
Old October 15th, 2007, 17:59   #13
Maverickmarc
 
Join Date: Sep 2007
Location: Barrie
Send a message via MSN to Maverickmarc
problem solved!!! thanx Derek
Maverickmarc is offline   Reply With Quote
ReplyTop


Go Back   Airsoft Canada > Discussion > Doctor's Corner

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Airsoft Canada
http://triggerairsoft.com/shop/

All times are GMT -4. The time now is 11:19.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.