AK47 not firing on full auto, fires on semi

mrsmellybelly · January 30th, 2006, 20:54

Ok ive had my ak for about 6 and a half months. its a great gun, outperforms my friends CA and ICS blah blah. Anyways, starting last weekend when i was at an airsoft game, it stopped firing in full auto. It just clicks, but when i switch to semi it fires in semi just fine. Ive tried 3 diff batteries from friends(which work in their guns), and they dont fix the full auto, though they all still fire the gun fine in semi. My gun isnt upgraded, i keep it lubed, the battery is an 8.4 1300mah nicad. The fuse isnt blown(obviously since it works in semi) but i was wondering if there was something that could have gone bad to do with the selection firing lever? I dunno, id really like to fix it before this weekends game though, thanks.

666 · January 30th, 2006, 21:19

Clicks like motor is trying to turn or just a trigger click? Sometimes two little copper pieces on the selector assembly located on the left side of the mechbox (left side when you shoulder the gun) bend inwards causing gun not to fire. You can try to pull out the mechbox and check those two pieces. Try to push them out a little. Be careful when you do it, those pieces are easy to break.

Greylocks · January 30th, 2006, 22:13

Or the gear timing may have finally gone out of sinc, or what 666 just said.
See a local expert. We're a little bit too far to help you.

mrsmellybelly · January 30th, 2006, 23:05

The motor is NOT trying to turn when i pull the trigger on auto, just the click from the actualy physical part of the trigger. Ill take it apart tommorow after school, ive taken a couple of airsoft guns completely apart before so it shouldnt be too bad. Cant be any worse than the ICS i took apart. Demon gun....ill update yall tommorow thanks for the help!

Greylocks · January 31st, 2006, 07:54

The AK has a few different ways to take apart. Check the guides first.

mrsmellybelly · January 31st, 2006, 15:36

Well, could someone tell me the easiest way to access the selector switch wires or whatever hes talking about?

666 · January 31st, 2006, 18:00

1. Remove dust cover and charging handle.
2.Remove the front. Four screws, two inside of magwell, two right next to magwell.
3. Remove pistol grip. Only one screw there.
4. Remove selector switch. Only one screw there.
5. Pull out the mechbox half way out, you should be able to see selector plate form there. If nessesery, disconnect mechbox from the wiring in the stock.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

January 30th, 2006, 20:54	#1
mrsmellybelly Trader rating Join Date: May 2005 Location: Charlotte	AK47 not firing on full auto, fires on semi Ok ive had my ak for about 6 and a half months. its a great gun, outperforms my friends CA and ICS blah blah. Anyways, starting last weekend when i was at an airsoft game, it stopped firing in full auto. It just clicks, but when i switch to semi it fires in semi just fine. Ive tried 3 diff batteries from friends(which work in their guns), and they dont fix the full auto, though they all still fire the gun fine in semi. My gun isnt upgraded, i keep it lubed, the battery is an 8.4 1300mah nicad. The fuse isnt blown(obviously since it works in semi) but i was wondering if there was something that could have gone bad to do with the selection firing lever? I dunno, id really like to fix it before this weekends game though, thanks.

January 30th, 2006, 21:19	#2
666 Trader rating Join Date: Jul 2004 Location: Toronto, Ontario	Clicks like motor is trying to turn or just a trigger click? Sometimes two little copper pieces on the selector assembly located on the left side of the mechbox (left side when you shoulder the gun) bend inwards causing gun not to fire. You can try to pull out the mechbox and check those two pieces. Try to push them out a little. Be careful when you do it, those pieces are easy to break. __________________ Op Woodsman. Biggest WW2 event in Ontario.

January 31st, 2006, 18:00	#7
666 Trader rating Join Date: Jul 2004 Location: Toronto, Ontario	1. Remove dust cover and charging handle. 2.Remove the front. Four screws, two inside of magwell, two right next to magwell. 3. Remove pistol grip. Only one screw there. 4. Remove selector switch. Only one screw there. 5. Pull out the mechbox half way out, you should be able to see selector plate form there. If nessesery, disconnect mechbox from the wiring in the stock. __________________ Op Woodsman. Biggest WW2 event in Ontario.

January 30th, 2006, 22:13	#3
Greylocks Trader rating Join Date: Dec 2001 Location: Gatineau, Quebec (Near Ottawa)	Or the gear timing may have finally gone out of sinc, or what 666 just said. See a local expert. We're a little bit too far to help you.

January 30th, 2006, 23:05	#4
mrsmellybelly Trader rating Join Date: May 2005 Location: Charlotte	The motor is NOT trying to turn when i pull the trigger on auto, just the click from the actualy physical part of the trigger. Ill take it apart tommorow after school, ive taken a couple of airsoft guns completely apart before so it shouldnt be too bad. Cant be any worse than the ICS i took apart. Demon gun....ill update yall tommorow thanks for the help!

January 31st, 2006, 07:54	#5
Greylocks Trader rating Join Date: Dec 2001 Location: Gatineau, Quebec (Near Ottawa)	The AK has a few different ways to take apart. Check the guides first.

January 31st, 2006, 15:36	#6
mrsmellybelly Trader rating Join Date: May 2005 Location: Charlotte	Well, could someone tell me the easiest way to access the selector switch wires or whatever hes talking about?

AK47 not firing on full auto, fires on semi

Doctor's Corner