Removing a Sector gear delay chip

DropTheBomb · August 9th, 2013, 19:47

im trying to replace some gears and ive been trying to remove the sector gear chip but it just wont come out, any suggestions? also is the chip necessary for the gun to function to properly?

HKGhost · August 9th, 2013, 19:49

No, the gun doesn't require the sector chip to function. It's only purpose is to delay the tappet plate so a bb will feed in high speed setup, or if you're tappet plate doesn't pull back the nozzle far enough to feed a bb. Just use a flat head screw driver and gently pry it up.

lurkingknight · August 9th, 2013, 20:15

what he said.

they start becoming more and more helpful the closer you get to 25rps... and over 30rps it's almost a requirement.

They do help with sluggish feeding though, so it's advantageous if you have slower feeding mags or ammo.

pestobanana · August 9th, 2013, 21:27

I use a razor blade to get stubborn clips unstuck, and then pliers to get them off.

As for sector delay clips being a requirement, I would disagree. I had problems with tappet plate pre-engagement at 32 RPS, so I removed the clip and even short stroked the tappet plate, feeding was perfect after that.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

August 9th, 2013, 19:47	#1
DropTheBomb Trader rating Join Date: Nov 2008 Location: Calgary, Alberta	Removing a Sector gear delay chip im trying to replace some gears and ive been trying to remove the sector gear chip but it just wont come out, any suggestions? also is the chip necessary for the gun to function to properly?

August 9th, 2013, 19:49	#2
HKGhost Trader rating Join Date: Nov 2009 Location: Mississauga, ON	No, the gun doesn't require the sector chip to function. It's only purpose is to delay the tappet plate so a bb will feed in high speed setup, or if you're tappet plate doesn't pull back the nozzle far enough to feed a bb. Just use a flat head screw driver and gently pry it up. __________________ Please email me as I'm not on ASC too often. Custom Build \| Upgrades \| Repairs \| Maintenance Contact: ghostgunwork@gmail.com / Private Message

August 9th, 2013, 20:15	#3
lurkingknight "bb bukakke" KING! Trader rating Join Date: Jul 2011 Location: Ottawa	what he said. they start becoming more and more helpful the closer you get to 25rps... and over 30rps it's almost a requirement. They do help with sluggish feeding though, so it's advantageous if you have slower feeding mags or ammo. __________________ I futz with V2s, V3s and V6s. I could be wrong... but probably, most likely not, as far as I know.

August 9th, 2013, 21:27	#4
pestobanana Squid Porn Superstar, I love the tentacles! Trader rating Join Date: Nov 2008 Location: Richmond Hill and Waterloo, Ontario	I use a razor blade to get stubborn clips unstuck, and then pliers to get them off. As for sector delay clips being a requirement, I would disagree. I had problems with tappet plate pre-engagement at 32 RPS, so I removed the clip and even short stroked the tappet plate, feeding was perfect after that.

Removing a Sector gear delay chip

Doctor's Corner