Airsoft Canada
https://www.replicaairguns.ca/airsoft

Go Back   Airsoft Canada > Discussion > Doctor's Corner
Home Forums Register Gallery FAQ Calendar
Retailers Community News/Info International Retailers IRC Today's Posts

slight hook to the right at about 100ft

:

Doctor's Corner

Reply
 
Thread Tools
Old May 10th, 2013, 14:15   #1
chaz
 
chaz's Avatar
 
Join Date: Jan 2006
Location: Ajax
slight hook to the right at about 100ft

Gun: CA M24
Barrel: Madbull 6.03
Bucking: shaved lonex w/ r-hop

The gun is shooting with a slight hook to the right each and every shot.
Need to pull it apart but I am almost positive the barrel is in straight. Perhaps the rhop needs a bit of trimming on the right side?

Any help would be greatly appreciated.
chaz is offline   Reply With Quote
Old May 10th, 2013, 14:25   #2
Hectic
Oh we do hate you, just never felt like wasting the time to give you a user title :P
 
Hectic's Avatar
 
Join Date: Apr 2007
Location: Toronto, Ontario
Could be the barrel/hop up unit is tilted a lil to the right
__________________
Quote:
Originally Posted by m102404 View Post
Hectic....FFS start writing in coherent sentences!!!
Quote:
Originally Posted by JDoorn View Post
Thanks Hectic,
While your posts are sometimes a difficult read, you sure are helpfull
Lvl. 3 certified sniper
FinchFieldAirsoft
Hectic is offline   Reply With Quote
Old May 10th, 2013, 14:48   #3
chaz
 
chaz's Avatar
 
Join Date: Jan 2006
Location: Ajax
So maybe a slight turn to the left of the whole barrel/hop up unit?
chaz is offline   Reply With Quote
Old May 10th, 2013, 14:54   #4
Hectic
Oh we do hate you, just never felt like wasting the time to give you a user title :P
 
Hectic's Avatar
 
Join Date: Apr 2007
Location: Toronto, Ontario
Yes or even just the barrel itself within the hop up. An easy way to test would be to crank up the hop up and use a light bb and see if it hooks big time then its for sure a lil twisted.
__________________
Quote:
Originally Posted by m102404 View Post
Hectic....FFS start writing in coherent sentences!!!
Quote:
Originally Posted by JDoorn View Post
Thanks Hectic,
While your posts are sometimes a difficult read, you sure are helpfull
Lvl. 3 certified sniper
FinchFieldAirsoft
Hectic is offline   Reply With Quote
Old May 10th, 2013, 15:01   #5
chaz
 
chaz's Avatar
 
Join Date: Jan 2006
Location: Ajax
Thanks!! I will give the barrel a slight turn. Guess I will just show up to the HILL super early tomorrow just in case I need to tweak more.
chaz is offline   Reply With Quote
Old May 10th, 2013, 15:21   #6
Trev140_0
 
Trev140_0's Avatar
 
Join Date: Sep 2011
I think you may have some paint stuck in the barrel.

Clean it out.
__________________
www.Hill437.com

"....Your life is ending one minute at a time..."

Trev140_0 is offline   Reply With Quote
Old May 10th, 2013, 16:10   #7
lurkingknight
"bb bukakke" KING!
 
Join Date: Jul 2011
Location: Ottawa
if everything lines up properly the following may apply

if you sanded the inner barrel side of the rhop patch, you may have not done it evenly and more pressure is being applied on the right side.
__________________
I futz with V2s, V3s and V6s. I could be wrong... but probably, most likely not, as far as I know.
lurkingknight is offline   Reply With Quote
Old May 10th, 2013, 16:39   #8
chaz
 
chaz's Avatar
 
Join Date: Jan 2006
Location: Ajax
Used the z kit so I didn't touch the inside of the patch. Just sanded the outside.

And trev, suck it
chaz is offline   Reply With Quote
Old May 10th, 2013, 16:49   #9
wind_comm
 
wind_comm's Avatar
 
Join Date: Jul 2011
Location: Calgary/Vancouver
what's the inside of the bucking look like? did you rotate it for an even surface? (totally guilty of not doing that sometimes)

it's likely just the barrel being slightly rotated as suggested, however.
__________________
too busy tinkering to play.
wind_comm is offline   Reply With Quote
Old May 10th, 2013, 17:14   #10
chaz
 
chaz's Avatar
 
Join Date: Jan 2006
Location: Ajax
I did NOT rotate the bucking. I will tear it down and confirm all of the above. Except for trevs suggestion.
chaz is offline   Reply With Quote
Old May 10th, 2013, 17:30   #11
Renegade)
A Total Bastard
 
Renegade)'s Avatar
 
Join Date: Apr 2006
Location: Tottenham, Ontario
Dirty barrel, damaged barrel, or bad hopup rubber/ unseated. Fully disassemble, inspect, clean, and re install the entire assembly and it should be fine. For best measure, replace the hopup rubber and nub.
__________________
W1-5
Renegade) is offline   Reply With Quote
Old May 10th, 2013, 17:57   #12
chaz
 
chaz's Avatar
 
Join Date: Jan 2006
Location: Ajax
Brand new barrel, rhop and bucking. Its user error. Going to turn the bucking and ensure the rhop is sanded flush and the barrel is in the hop up chamber perfectly centered.
chaz is offline   Reply With Quote
Old May 10th, 2013, 18:45   #13
KenTsui
 
Join Date: Dec 2011
Quote:
Originally Posted by chaz View Post
Brand new barrel, rhop and bucking. Its user error. Going to turn the bucking and ensure the rhop is sanded flush and the barrel is in the hop up chamber perfectly centered.
Yea, because even if you didn't touch the inside of the patch, if the outside of the patch is uneven, it could produce uneven pressure on the bb.
KenTsui is offline   Reply With Quote
Old May 10th, 2013, 22:01   #14
Chiba
 
Join Date: Jul 2011
Location: Markham
On ASM, HS5 has suggested to turn the inner barrel alittle to compensate.
Chiba is offline   Reply With Quote
Old May 10th, 2013, 22:03   #15
coach
aka coachster
 
coach's Avatar
 
Join Date: Mar 2008
Location: T dot
Bent barrel
coach is offline   Reply With Quote
ReplyTop


Go Back   Airsoft Canada > Discussion > Doctor's Corner

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Airsoft Canada
https://www.replicaairguns.ca/airsoft

All times are GMT -4. The time now is 22:23.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.