Misfeeding With Sector Clip?

iKliiu · July 19th, 2011, 14:00

In my G36, I recently went to adjust the AOE and do a minor check up. After reassembly, it would misfeed at times.

I'm guessing that is something to do with the tappet plate, but there is no wear on it.

Any suggestions?

HKGhost · July 19th, 2011, 14:47

Did you check the hop up? The bucking could be out of alignment. What else did you change?

iKliiu · July 19th, 2011, 15:38

Hop up is fine. I also reshimmed, just that probably doesn't have anything to do with misfeeding.

IggysPiggy · July 20th, 2011, 17:10

I personally would check your mag well alignment as well as where the wires are being run inside the the body (above the magwell). a little filling love to the feed tube on the magwell adapter does wonders for the G36 as well (round out any sharp edges).

iKliiu · July 25th, 2011, 00:11

Still no luck. I checked the alignment several times.

The gun feeds upside down and also feeds when bbs are just dropped in the magwell.

I've tried different mags, bbs, etc, but it only feeds upside down.

slink182 · July 25th, 2011, 12:36

Check your magazines. They may require a light shot of silicone oil. The BBs and/or the spring may be binding in the mag.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

July 19th, 2011, 14:00	#1
iKliiu Trader rating Join Date: Aug 2010	Misfeeding With Sector Clip? In my G36, I recently went to adjust the AOE and do a minor check up. After reassembly, it would misfeed at times. I'm guessing that is something to do with the tappet plate, but there is no wear on it. Any suggestions?

July 19th, 2011, 14:47	#2
HKGhost Trader rating Join Date: Nov 2009 Location: Mississauga, ON	Did you check the hop up? The bucking could be out of alignment. What else did you change? __________________ Please email me as I'm not on ASC too often. Custom Build \| Upgrades \| Repairs \| Maintenance Contact: ghostgunwork@gmail.com / Private Message

July 19th, 2011, 15:38	#3
iKliiu Trader rating Join Date: Aug 2010	Hop up is fine. I also reshimmed, just that probably doesn't have anything to do with misfeeding.

July 20th, 2011, 17:10	#4
IggysPiggy Trader rating Join Date: Sep 2007	I personally would check your mag well alignment as well as where the wires are being run inside the the body (above the magwell). a little filling love to the feed tube on the magwell adapter does wonders for the G36 as well (round out any sharp edges).

July 25th, 2011, 00:11	#5
iKliiu Trader rating Join Date: Aug 2010	Still no luck. I checked the alignment several times. The gun feeds upside down and also feeds when bbs are just dropped in the magwell. I've tried different mags, bbs, etc, but it only feeds upside down.

Misfeeding With Sector Clip?

Doctor's Corner