Airsoft Canada

Go Back   Airsoft Canada > Discussion > Doctor's Corner
Home Forums Register Gallery FAQ Calendar
Retailers Community News/Info International Retailers IRC Today's Posts

ASCU technical discussion

:

Doctor's Corner

Reply
 
Thread Tools
Old October 19th, 2011, 19:24   #151
audi_bhoy
 
Join Date: Mar 2009
Location: Trois-Rivières
Use the M-93 Motor from ebairsoft.com, low cost, high magnets, and powerful enought (would cause overspin without the ASCU in single shooting)
audi_bhoy is offline   Reply With Quote
Old October 27th, 2011, 10:09   #152
rames
 
Join Date: Oct 2011
OK, I made some modifications.
Problem was in air leak between air nozzle and bucking.
Tappet plates (it is new) front side was bent to back and air nozzle does not moved enough to forward. I've heated tappet plate, made 90 degree of front side of tappet plate and air nozzle goes far of.
Also, i've increased length of hopup spring.
After this modifications FPS is increased from 440FPS to 482FPS. This result is with Guarder SP140 spring.
I will research further, because I think currently it have air leak also, because with SP140 it is bad result.

Last edited by rames; October 27th, 2011 at 10:13..
rames is offline   Reply With Quote
Old November 6th, 2011, 03:31   #153
mr_nuts31
 
mr_nuts31's Avatar
 
Join Date: Aug 2009
Location: Petawawa, ON
Quote:
Originally Posted by coachster View Post
You can splice in any low resistance wires to the motor. I highly recommend soldering(avoid cold joints) them instead of just twisting and taping.

Also avoid any solid core wires.
I did just that and when I plugged in the battery, the motor constantly spins and I hear no beeping. Somehow I think I fucked up the control unit.
mr_nuts31 is offline   Reply With Quote
Old November 7th, 2011, 15:30   #154
Nortus
 
Join Date: Dec 2001
Location: Richmond Hill, Ontario
Where can we get replacement data cables?
Nortus is offline   Reply With Quote
Old November 7th, 2011, 21:01   #155
juicyjust
 
juicyjust's Avatar
 
Join Date: Jul 2011
Location: St-Hubert, Qc
Connectors

Quote:
Originally Posted by Nortus View Post
Where can we get replacement data cables?


You can get part H1565-ND for the connetor and H1577CT-ND for the pins from digikey.ca to replace the connectors.

The pins are a pain to fit, so order 100 to make sure

Just

Last edited by juicyjust; November 7th, 2011 at 21:04..
juicyjust is offline   Reply With Quote
Old November 9th, 2011, 01:26   #156
CJay
 
CJay's Avatar
 
Join Date: Oct 2008
Location: Belle River, ON
or u go to airsoftparts.ca and just order a new data cable that will fit without fucking around with annoying small pins that break lol...
__________________
"Creator of the Zombat Sniper - oh yeah baby"
CJay is offline   Reply With Quote
Old November 9th, 2011, 08:05   #157
coach
aka coachster
 
coach's Avatar
 
Join Date: Mar 2008
Location: T dot
Quote:
Originally Posted by CJay View Post
or u go to airsoftparts.ca and just order a new data cable that will fit without fucking around with annoying small pins that break lol...
Dude, tone It back a bit. Take a look yourself at airsoftparts and try to find it first.
coach is offline   Reply With Quote
Old January 27th, 2012, 13:32   #158
gman3850
 
Join Date: Jan 2012
ok ive red through most of the thread and seem to find the answers but their not working

i just installed and im getting over spin on every motor i have in full auto and that makes it do a quick click and then stop, it worked fine first mag (60rds) than it started sounding funny after i plugged battery back in to change mood. the beep sound went from crisp to scrachy and the ab doesnt work, i have changed lipos and tryed all the moods
i have
matrix turbo
g&p 120
aim f430 spider torque motor
aim f430i high speed
stock j motor

no matter which one they all over rotate

Last edited by gman3850; January 27th, 2012 at 13:35..
gman3850 is offline   Reply With Quote
Old January 27th, 2012, 14:50   #159
SuperHog
 
SuperHog's Avatar
 
Join Date: Jul 2011
Location: Toronto, Ontario
That micro switch looks fragile. What are you guys doing to prevent the trigger from breaking it if pulled too hard?
SuperHog is offline   Reply With Quote
Old April 9th, 2012, 14:11   #160
Cobrajr122
2 Cent Tactical
 
Cobrajr122's Avatar
 
Join Date: Apr 2006
Location: NB
After my TM stock trigger contacts took a shit on me a few months ago I decided that it would be a great time to buy the ASCU and try it out.

Ever since I have installed this thing my rifle has not been useable. At the same time I was also posted away to go on course and I am finally back in a situation where I have my rifle again and can try to get it fixed. Getting it fixed is top priority for me right now since Echo1 shit the bed with the trigger design for the M240. I JUST replaced it and it broke again before i could even fucking game it >_>

I NEVER had ANY problems with the rifle until the trigger contacts bit the dust.

The problem: Shoots once or twice then gives me 2 buzzes and does not shoot again unless I re-connect the battery.

According to the manual this could be a few things.

1. Tight shimming
2. Motor too high
3. Poor battery
4. Weak motor
5. Broken gear
-----------------------------
1. Gears spin freely, even tried shimming them loose.

2. Tried every height setting, even removed the highest adjustment compleatly.

3. Tried with multiple charged batteries, all 9.6V and one 7.4V 20C Lipo.

4. JUST replaced the stock TM EG MAX Hyper 1000 with a G&P M120 today.
Gun is only shooting 350 FPS on 0.2g, so not a very strong spring anyways. It was shooting 380 when I bought it back in 2008.

5. Gears are fine.

This is really pissing me off. I would like to see the ASCU work but if I have to go back to mechanical trigger mech I will.
Cobrajr122 is offline   Reply With Quote
Old April 9th, 2012, 15:52   #161
HKGhost
 
HKGhost's Avatar
 
Join Date: Nov 2009
Location: Mississauga, ON
Did you check to make sure that the cutoff lever is tripping the unit? Some cutoff lever (worn ones) won't go up high enough to trip the unit in SEMI. Either bend the cutoff lever (if it's steel) so as the sector gear goes around, it tips the cutoff lever higher, or get a new one.
__________________
Please email me as I'm not on ASC too often.

Custom Build | Upgrades | Repairs | Maintenance
Contact: ghostgunwork@gmail.com / Private Message
HKGhost is offline   Reply With Quote
Old April 9th, 2012, 16:23   #162
Cobrajr122
2 Cent Tactical
 
Cobrajr122's Avatar
 
Join Date: Apr 2006
Location: NB
How high should it be going up?
Its moving a good 4mm ish and was tripping the mechanical trigger mech just fine.

I would assume that the unit would not stop spinning the motor if it was not tripped by the cutoff leaver.

Last edited by Cobrajr122; April 9th, 2012 at 16:25..
Cobrajr122 is offline   Reply With Quote
Old April 9th, 2012, 16:43   #163
H1TMAN
formerly GRoy
 
H1TMAN's Avatar
 
Join Date: Dec 2008
Location: Angus, ON
I had the same issue with mine and the issue was a worn down cut-off lever. I would get and new one and try that.
H1TMAN is offline   Reply With Quote
Old April 9th, 2012, 18:57   #164
HKGhost
 
HKGhost's Avatar
 
Join Date: Nov 2009
Location: Mississauga, ON
Quote:
Originally Posted by Cobrajr122 View Post
How high should it be going up?
Its moving a good 4mm ish and was tripping the mechanical trigger mech just fine.

I would assume that the unit would not stop spinning the motor if it was not tripped by the cutoff leaver.
Just fine isn't good enough. The lever on the trigger should go completely up. You're getting off a few shots then the unit realize there's nothing tripping the unit off, so it goes "beep" then shuts off. I've see this many times now, and most of it was due to worn cutoff lever, or it wasn't tripping the unit off.
__________________
Please email me as I'm not on ASC too often.

Custom Build | Upgrades | Repairs | Maintenance
Contact: ghostgunwork@gmail.com / Private Message
HKGhost is offline   Reply With Quote
Old April 9th, 2012, 19:13   #165
Amos
 
Amos's Avatar
 
Join Date: Aug 2006
Location: Japan
Don't use a prommy cut off lever though. They're too big and will snap the sensor arm off.
__________________
Custom Builds:
FA3674U
Krinkov
G3SD6
Amos is offline   Reply With Quote
ReplyTop


Go Back   Airsoft Canada > Discussion > Doctor's Corner

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Airsoft Canada

All times are GMT -4. The time now is 13:53.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.