|
|||||||||
|
Home | Forums | Register | Gallery | FAQ | Calendar |
Retailers | Community | News/Info | International Retailers | IRC | Today's Posts |
|
Thread Tools |
March 5th, 2008, 23:52 | #1 |
Desert Eagle clip not holding gas
I'm at a loss. I used my DE around Christmas 07, no problems. Went to use it the other day, the clip refuses to hold gas. I tried green gas, coleman propane, nothing holds. Instead, the clip literally drops below 0* celcius while holding it
What should I do. To answer a possible question, it was semi cold outside when I was trying to load gas
__________________
Lower Mainland Airsoft Group Bolt Action L3; G-Spec @ 500 w/.20's G3 @ Broken Down MP5 @ 325 w/.20's MP5K @ 280 w/.20's |
|
March 5th, 2008, 23:57 | #2 |
the seals could cracked??
PS/its not a clip its a mag |
|
March 6th, 2008, 00:01 | #3 |
do it inside where its warm? did you do it properly for loading it? And finally does it expel out the exit?
|
|
March 6th, 2008, 00:03 | #4 |
do you hold the propain canister upside down, wont work other wise
|
|
March 6th, 2008, 00:27 | #5 |
Yep, I hold the clip and gas can properly
Yep, it expells out of the exit area, don't know for sure I hope I the seals ain't cracked And finally. I think I got it fixed anyways. The screw at the bottom of the clip was slightly loose, and there was a small steel rod near the top going from side to side that needed to be pushed over a bit. PS. I always thought it to be a "clip" for a pistol, and a "mag" for a rifle
__________________
Lower Mainland Airsoft Group Bolt Action L3; G-Spec @ 500 w/.20's G3 @ Broken Down MP5 @ 325 w/.20's MP5K @ 280 w/.20's |
|
March 6th, 2008, 00:36 | #6 |
It's "magazine" for everything except, for example, the M1 Garand or Kar98, which use clips.
|
|
March 6th, 2008, 15:53 | #7 |
where is the weak. check the bottom or side for a screw and tighten it. Mine back out on my hicapa mags. But its an easy fix for me. If this isn't the problem we can at least rule that one out. Who makes it?
|
|
March 6th, 2008, 16:04 | #8 |
Red Wine & Adderall
|
Well after the last time you used it, if you didnt store it with gas in the mag its very possible the mag dried out. Tighten anything thats loose and maybe that should fix everything. If not hopefully a good soak in silicone oil for a few hours or over night may remedy the issue. If not you will have to replace some Orings.
__________________
"Its only a little bit on fire" |
March 7th, 2008, 01:10 | #9 |
silicone.... keep gassed and warm... unload when not in use... all that jazz.
__________________
|
|
March 7th, 2008, 22:34 | #10 | |
Quote:
__________________
Lower Mainland Airsoft Group Bolt Action L3; G-Spec @ 500 w/.20's G3 @ Broken Down MP5 @ 325 w/.20's MP5K @ 280 w/.20's |
||
March 7th, 2008, 22:38 | #11 |
Red Wine & Adderall
|
Yes, you are supposed to leave some gas in the mag. Some say keep it full, some say to keep only a few seconds worth of a fill inside, but either way its suggested to keep gas in the mag when the mag is not in use.
__________________
"Its only a little bit on fire" |
March 7th, 2008, 23:08 | #12 | |
Official ASC Bladesmith
|
Quote:
Sort out where exactly your mag is leaking, then we can move on to fix solutions. Different areas require different fixes. |
|
|
Bookmarks |
Thread Tools | |
|
|