|
|
|
|
|
||||||||
|
|
|||||||||
| Home | Forums | Register | Gallery | FAQ | Calendar |
| Retailers | Community | News/Info | International Retailers | IRC | Today's Posts |
 |
|
|
Thread Tools |
October 15th, 2007, 17:25
|
#1 |
|
TM P226 question
Just got it in today. Lubed it up. Ran a mag throught it and decided to take it apart. just the slide though. Slide comes off no problem. Dropped sum silicone oil were the slide moves and now it wont go back in all the way. Theres like a feww milimetres left for it to go. WTF!! I'm gonna rage..
Someone help before I do |
|
|
|
|
October 15th, 2007, 17:28
|
#2 |
 A Total Bastard
|
Chill before you break it man, push down the silver peice on the left side of the hammer assembly, this engages the firing pin, the slide wont go back unless this is locked down or able to move freely. When the pin is back, the lever is locked, but when it pin is released, the lever can move up and down allowing the slide to rack back fully.
Im in Orillia BTW, so if you need a 226 lesson/walk through, and age verification, come for a 20 minute drive in the future.
__________________
W1-5 |
|
|
|
|
October 15th, 2007, 17:35
|
#3 |
|
i'm looking @ the hammer assembly. the only silver piece in the is on the left side if ur looking down the gun. it moves up and down but its spring loaded and comes back up.
|
|
|
|
|
|
October 15th, 2007, 17:38
|
#4 |
|
the slide moves freely and almost comes back, theres just a few mm left for it to be on properly
|
|
|
|
|
|
October 15th, 2007, 17:38
|
#5 |
|
A Total Bastard
|
as long as it moves up and down, and the hammer is locked back, the slide should slide right on and all the way back allowing you to relock the release lever. Try it again, if not, dont force it, pull the slide back off, pull the trigger to release the hammer, then recock it and try to put the slide back on.
Let me know.
__________________
W1-5 |
|
|
|
|
October 15th, 2007, 17:42
|
#6 |
|
no luck
|
|
|
|
|
|
October 15th, 2007, 17:45
|
#7 |
|
its almost there
|
|
|
|
|
|
October 15th, 2007, 17:45
|
#8 |
|
When putting the P226 slide back on, if you just slide it on it will stop about 2 mm or so from the normal place.
I noticed that you have to use your thumb to push the slide/barrel back that 2mm abit, and then flick the disassembly switch back up. I hope this info helps.
__________________
"Banning firearms to prevent criminal use of guns is about as smart as banning marriage to prevent spousal abuse, or banning pregnancy to prevent child abuse. " "When just seconds can mean life or death, the police are just minutes away" "If you can read this, thank a teacher... Since it's in English, thank a soldier" |
|
|
|
|
October 15th, 2007, 17:48
|
#9 |
|
i'm trying to force that 2mm a bit but not to hard. it won't budge
|
|
|
|
|
|
October 15th, 2007, 17:48
|
#10 |
|
A Total Bastard
|
hmm, im not sure what it could be, bent hammer rod, mag in? lever isnt aimed down(how u turn it to release the slide) maybe the recoil spring rod is not in correctly?
Take this to msn if you want.. easier to work on there.
__________________
W1-5 |
|
|
|
|
October 15th, 2007, 17:48
|
#11 |
|
but thats definatly where its stopping, its like its caught on something
|
|
|
|
|
|
October 15th, 2007, 17:49
|
#12 |
|
|
|
|
October 15th, 2007, 17:59
|
#13 |
|
problem solved!!! thanx Derek
|
|
|
|
|
 |
|
||||||
| Bookmarks |
| Thread Tools | |
|
|
 |
|
