WE M4 GBBR - Trademark lower doesn't fit blank upper, is that normal?

tome · April 7th, 2015, 09:44

Hi,

I have a factory open-bolt m4 with a blank body and a spare receiver set which seems to be a v1 Colt trademarked, originally close bolt.

The uppers and lowers don't fit when switched between sets. Is this normal or do I have a (or both) misshappen receivers. Is there some modification I can make to make them fit?

Thanks for any advice.

SF_Chewy · April 7th, 2015, 15:27

Happened to me too.

I have a WE M4 (no trades), then I bought a new WE upper to make a CQB build. I found out after trying to reassemble it that it was all out of tolerance. Nothing fit well into it, and still needs modding to fit properly. All the pins wouldn't fit properly from one upper to the next.

So I would chalk this up to poor tolerances from the WE factory. You may need to sand and/or grind one piece so that it fits into the other.

Thenooblord · April 7th, 2015, 15:53

its tolerances, some of my uppers and lowers just wouldnt work together, but fine with others

tome · April 9th, 2015, 11:28

Thanks for the replies guys. Glad to hear I'm not crazy haha

BioRage · April 9th, 2015, 11:30

Each batch of WE have different specs over the years. This has been verified by Angry Guns.

So as an example, if you have a older variant of then WE M4 body, it will not be on spec with one you picked up recently.

tome · April 9th, 2015, 11:46

Cheers! Confirmed by Angry Gun

I guess moral of the story for me is if I want a lower and interchangable uppers I should buy multiple uppers and a single lower at the same time :P

Not that it's easy to come by lowers here!

uncle_benny12 · April 9th, 2015, 14:29

I had the same issue trying to fit a Colt traded lower onto a new WE M4 I purchased last year.

I just had to slowly file away some material on the holes of the lower receiver. It fits now but it's tight enough that I need to use a punch to take it apart.

tome · April 9th, 2015, 14:39

Quote:

Originally Posted by uncle_benny12

I had the same issue trying to fit a Colt traded lower onto a new WE M4 I purchased last year.

I just had to slowly file away some material on the holes of the lower receiver. It fits now but it's tight enough that I need to use a punch to take it apart.

Yeah, that's how the upper that came with the traded set fits with my blank lower, funnily enough. I need to tap the rear pin to get it out.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

April 7th, 2015, 09:44	#1
tome Trader rating Join Date: Sep 2007 Location: Toronto	WE M4 GBBR - Trademark lower doesn't fit blank upper, is that normal? Hi, I have a factory open-bolt m4 with a blank body and a spare receiver set which seems to be a v1 Colt trademarked, originally close bolt. The uppers and lowers don't fit when switched between sets. Is this normal or do I have a (or both) misshappen receivers. Is there some modification I can make to make them fit? Thanks for any advice. __________________ aka - Donkey Balls

April 9th, 2015, 11:28	#4
tome Trader rating Join Date: Sep 2007 Location: Toronto	Thanks for the replies guys. Glad to hear I'm not crazy haha __________________ aka - Donkey Balls

April 9th, 2015, 11:46	#6
tome Trader rating Join Date: Sep 2007 Location: Toronto	Cheers! Confirmed by Angry Gun I guess moral of the story for me is if I want a lower and interchangable uppers I should buy multiple uppers and a single lower at the same time :P Not that it's easy to come by lowers here! __________________ aka - Donkey Balls

April 7th, 2015, 15:27	#2
SF_Chewy Trader rating Join Date: Mar 2010	Happened to me too. I have a WE M4 (no trades), then I bought a new WE upper to make a CQB build. I found out after trying to reassemble it that it was all out of tolerance. Nothing fit well into it, and still needs modding to fit properly. All the pins wouldn't fit properly from one upper to the next. So I would chalk this up to poor tolerances from the WE factory. You may need to sand and/or grind one piece so that it fits into the other.

April 9th, 2015, 11:30	#5
BioRage Trader rating Join Date: Nov 2008 Location: Toronto	Each batch of WE have different specs over the years. This has been verified by Angry Guns. So as an example, if you have a older variant of then WE M4 body, it will not be on spec with one you picked up recently.

April 9th, 2015, 14:29	#7
uncle_benny12 Trader rating Join Date: Jan 2003	I had the same issue trying to fit a Colt traded lower onto a new WE M4 I purchased last year. I just had to slowly file away some material on the holes of the lower receiver. It fits now but it's tight enough that I need to use a punch to take it apart.

WE M4 GBBR - Trademark lower doesn't fit blank upper, is that normal?

Doctor's Corner