Ptw mag help

Katlyn Cage · August 21st, 2014, 00:52

Ok so the quick and easy is I can't load my mags.
I am using a speed loader, no adapter. And the bbs keep shooting all over the place.

So basically I'm new to ptws and have no clue what I'm doing wrong.
The mags are a stock a&k ptw mag and three different pts ptw emags

FreelancerInc · August 21st, 2014, 01:10

should work aslong as you have everything lined up proper...use one hand to hold the mag. the other to hold the speed-loader...BUT use 2 fingers on either side of the mag "teeth" to make sure the bb's go in.....

hard to explain but i hope that works for ya

Ricochet · August 21st, 2014, 01:22

There's two little teeth (as Freelancer mentioned) on either side of the BB port. Are the BBs shooting out of the loader while trying to get them in the mag, or are they shooting out of the mag after you pull the loader away?

For the latter, you can use the sides of the loader to at least partially hold the teeth down and it should load smoothly. What's you mag capacity and approximately how many rounds does your loader eject on a single stroke? The reason I ask is because many of us PTW users only ever half load out magazines, which saves them long term. So for instance my mag takes 120 to fill so I only load about sixty per mag total. My loader ejects five BBs per stroke, so I only give each mag about 12 total strokes.

If they are shooting back out of the mag after it is likely because those teeth we were talking about aren't coming back up into place. Also I recommend Systema mags over any of the clones. They are a bit more, but nine years later and all of mine still work like new.

Katlyn Cage · August 21st, 2014, 01:31

The bbs are firing out of the mag after loading, they are 120 end mags but I have only tried loading 10 or so bbs just to test them out.

Btw does anyone know how to attract all the bbs on the floor before they multiply as we all know they do!

Ricochet · August 21st, 2014, 02:40

It's your teeth being stuck down then. What can happen is they come rough or too wide and they'll stick in their slots. To rectify this gently file the sides of them down. A women's compressed foam nail file works best. Be careful not to lose the little springs underneath them. They are very small and hard to find.

Katlyn Cage · August 21st, 2014, 02:51

i will file them in the morning and post my results.

also. is it helpful to file a notch into my speed loader lip to avoid the teeth? looks like thats what the adapters do.

Ricochet · August 21st, 2014, 02:57

Could be, it would depend on your adapter.

Katlyn Cage · August 21st, 2014, 16:52

So the filing of the fingers worked on two pts mags. Not the stock mag son done pts mag. The fingers look completely worn down where they hold the bbs. Is there anywhere to get replacement ones? And a finger spring? Aparently once they pop they are lost forever.

DipTwit · August 22nd, 2014, 16:15

Ouch, I feel your pain - I've been repairing lots of my mags, but because I bought second-hand PMAGs and some of their internals were worn out.

Curiously, I have 5 A&K PTW mags and they are the ones that have worked flawlessly- I think you just got rotten luck with yours. Their manufacturing QA does need some work though, I got one mag that came missing a lever inside it, so the bolt-stop didn't work.

I don't know where to buy replacements for the feed lips, or their springs - I bought someone's bag of spare magazine inners just so I would have a bunch of spare parts. Someone want to chime in? I wouldn't mind knowing where to get them either

Wli · August 22nd, 2014, 17:33

You could try scopesandlasers. I don't remember the exact url but it's a guy in Hong Kong that has the most random bits you could ask for when it comes to airsoft stuff. I don't remember if they have exactly those pieces but they do sell ptw mag inner so last resort I suppose.

Ricochet · August 22nd, 2014, 20:11

You can purchase just the mag internals as a whole as well. I recommend paying the extra bit for Systema mags. After using Vanaras and a few other types I've gone back to strictly Systema.

Ranger11 · September 30th, 2014, 03:07

I've had good luck with my PTS mags, not a single issue with them, and damn do they ever take a good old beating!

As for the feed lips and springs, you can get them from Tac, Anthony Gnapp is his Facebook name, Tackleberry is his name on the systema PTW forums

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

August 21st, 2014, 00:52	#1
Katlyn Cage Trader rating Join Date: Jun 2010 Location: Medicine Hat, AB	Ptw mag help Ok so the quick and easy is I can't load my mags. I am using a speed loader, no adapter. And the bbs keep shooting all over the place. So basically I'm new to ptws and have no clue what I'm doing wrong. The mags are a stock a&k ptw mag and three different pts ptw emags

August 21st, 2014, 01:10	#2
FreelancerInc Trader rating Join Date: Apr 2011 Location: Brooks Alberta Canada	should work aslong as you have everything lined up proper...use one hand to hold the mag. the other to hold the speed-loader...BUT use 2 fingers on either side of the mag "teeth" to make sure the bb's go in..... hard to explain but i hope that works for ya __________________ Forums Rules, Learn em, Love em Follow em I have gear and gun rentals available at all Team SWATT hosted games in Brooks, Alberta

August 21st, 2014, 01:22	#3
Ricochet How much sand CAN you fit in your vagina!? Trader rating Join Date: Feb 2008 Location: North Delta, BC (Greater Vancouver)	There's two little teeth (as Freelancer mentioned) on either side of the BB port. Are the BBs shooting out of the loader while trying to get them in the mag, or are they shooting out of the mag after you pull the loader away? For the latter, you can use the sides of the loader to at least partially hold the teeth down and it should load smoothly. What's you mag capacity and approximately how many rounds does your loader eject on a single stroke? The reason I ask is because many of us PTW users only ever half load out magazines, which saves them long term. So for instance my mag takes 120 to fill so I only load about sixty per mag total. My loader ejects five BBs per stroke, so I only give each mag about 12 total strokes. If they are shooting back out of the mag after it is likely because those teeth we were talking about aren't coming back up into place. Also I recommend Systema mags over any of the clones. They are a bit more, but nine years later and all of mine still work like new. __________________ I have developed a new sport called Airhard. Pretty much the same as Airsoft, except you have to maintain an erection...

August 21st, 2014, 01:31	#4
Katlyn Cage Trader rating Join Date: Jun 2010 Location: Medicine Hat, AB	The bbs are firing out of the mag after loading, they are 120 end mags but I have only tried loading 10 or so bbs just to test them out. Btw does anyone know how to attract all the bbs on the floor before they multiply as we all know they do!

August 21st, 2014, 02:40	#5
Ricochet How much sand CAN you fit in your vagina!? Trader rating Join Date: Feb 2008 Location: North Delta, BC (Greater Vancouver)	It's your teeth being stuck down then. What can happen is they come rough or too wide and they'll stick in their slots. To rectify this gently file the sides of them down. A women's compressed foam nail file works best. Be careful not to lose the little springs underneath them. They are very small and hard to find. __________________ I have developed a new sport called Airhard. Pretty much the same as Airsoft, except you have to maintain an erection...

August 21st, 2014, 02:51	#6
Katlyn Cage Trader rating Join Date: Jun 2010 Location: Medicine Hat, AB	i will file them in the morning and post my results. also. is it helpful to file a notch into my speed loader lip to avoid the teeth? looks like thats what the adapters do.

August 21st, 2014, 02:57	#7
Ricochet How much sand CAN you fit in your vagina!? Trader rating Join Date: Feb 2008 Location: North Delta, BC (Greater Vancouver)	Could be, it would depend on your adapter. __________________ I have developed a new sport called Airhard. Pretty much the same as Airsoft, except you have to maintain an erection...

August 21st, 2014, 16:52	#8
Katlyn Cage Trader rating Join Date: Jun 2010 Location: Medicine Hat, AB	So the filing of the fingers worked on two pts mags. Not the stock mag son done pts mag. The fingers look completely worn down where they hold the bbs. Is there anywhere to get replacement ones? And a finger spring? Aparently once they pop they are lost forever.

August 22nd, 2014, 16:15	#9
DipTwit Trader rating Join Date: Oct 2012 Location: Alberta	Ouch, I feel your pain - I've been repairing lots of my mags, but because I bought second-hand PMAGs and some of their internals were worn out. Curiously, I have 5 A&K PTW mags and they are the ones that have worked flawlessly- I think you just got rotten luck with yours. Their manufacturing QA does need some work though, I got one mag that came missing a lever inside it, so the bolt-stop didn't work. I don't know where to buy replacements for the feed lips, or their springs - I bought someone's bag of spare magazine inners just so I would have a bunch of spare parts. Someone want to chime in? I wouldn't mind knowing where to get them either

August 22nd, 2014, 17:33	#10
Wli Trader rating Join Date: Sep 2013 Location: Toronto	You could try scopesandlasers. I don't remember the exact url but it's a guy in Hong Kong that has the most random bits you could ask for when it comes to airsoft stuff. I don't remember if they have exactly those pieces but they do sell ptw mag inner so last resort I suppose.

August 22nd, 2014, 20:11	#11
Ricochet How much sand CAN you fit in your vagina!? Trader rating Join Date: Feb 2008 Location: North Delta, BC (Greater Vancouver)	You can purchase just the mag internals as a whole as well. I recommend paying the extra bit for Systema mags. After using Vanaras and a few other types I've gone back to strictly Systema. __________________ I have developed a new sport called Airhard. Pretty much the same as Airsoft, except you have to maintain an erection...

September 30th, 2014, 03:07	#12
Ranger11 Extra Salty and vinegar Trader rating Join Date: Apr 2013 Location: Red Deer, Alberta	I've had good luck with my PTS mags, not a single issue with them, and damn do they ever take a good old beating! As for the feed lips and springs, you can get them from Tac, Anthony Gnapp is his Facebook name, Tackleberry is his name on the systema PTW forums

Ptw mag help

Doctor's Corner